Hi Geert,
Thank you for the review.
On Tue, Nov 24, 2020 at 9:04 AM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
>
> Hi Prabhakar,
>
> On Fri, Nov 20, 2020 at 4:13 PM Lad Prabhakar
> <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> wrote:
> > Add the ov7725 endpoint nodes to the camera daughter board. The ov7725
> > sensors can be populated on I2C{0,1,2,3} buses.
> >
> > By default the VIN{0,1,2,3} are tied to OV5640{0,1,2,3} endpoints
> > respectively in the camera DB dts hence the remote-endpoint property in
> > OV7725{0,1,2,3} endpoints is commented out.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
>
> Thanks for your patch!
>
> The camera definitions look mostly OK to me.
>
> IIUIC, these are 4 plug-in cameras, that can be used instead of the
> (currently described) 4 other OV5640-based plug-in cameras?
> In addition, the user can mix and match them, in the 4 available
> slots (J11-J14), which would require editing the DTS?
>
> Wouldn't it be easier to have separate DTS files for the OV7725 and
> OV5640 cameras, and #include them from r8a7742-iwg21d-q7-dbcm-ca.dts?
>
Good point, will move the vin and ov5640 nodes to
r8a7742-iwg21d-q7-dbcm-ov5640.dtsi and similarly add vin and ov7725
nodes to r8a7742-iwg21d-q7-dbcm-ov7725.dtsi and by default shall
include r8a7742-iwg21d-q7-dbcm-ov5640.dtsi in
r8a7742-iwg21d-q7-dbcm-ca.dts file.(Will keep the mclk_camx and
pimuxes in r8a7742-iwg21d-q7-dbcm-ca.dts file)
> /* 8bit CMOS Camera 1 (J13) */
> #define MCLK_CAM &mclk_cam1
> #define ...
> /* Comment the below according to connected cameras */
> #include "ov5640.dts"
> //#include "ov7725.dts"
> #undef MCLK_CAM
> #undef ...
>
> [...]
>
> > --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
> > +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
>
> > @@ -152,6 +198,30 @@
> > };
> > };
> > };
> > +
> > + ov7725@21 {
> > + status = "disabled";
>
> This one is disabled, the three others aren't?
>
my bad should have dropped this.
Cheers,
Prabhakar
> > + compatible = "ovti,ov7725";
> > + reg = <0x21>;
> > + clocks = <&mclk_cam3>;
> > +
> > + port {
> > + ov7725_2: endpoint {
> > + bus-width = <8>;
> > + bus-type = <6>;
> > + /*
> > + * uncomment remote-endpoint property to
> > + * tie ov7725_2 to vin2ep also make
> > + * sure to comment/remove remote-endpoint
> > + * property from ov5640_2 endpoint and
> > + * replace remote-endpoint property in
> > + * vin2ep node with
> > + * remote-endpoint = <&ov7725_2>;
> > + */
> > + /* remote-endpoint = <&vin2ep>; */
> > + };
> > + };
> > + };
> > };
>
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
