On 11/9/2020 8:35 AM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal@xxxxxxxxxx>
>
> Power Management Controller can be found on BCM4908 and is needed to
> power on SoC blocks. It can be controlled using:
> 1. Firmware calls
> 2. Direct regs access
>
> Only the later method is supported by this initial driver. It was
> successfully tested on BCM4908 using HCD controllers.
>
> Signed-off-by: Rafał Miłecki <rafal@xxxxxxxxxx>
> ---
[snip]
> +#define PMBM_CTRL 0x00
> +#define PMC_PMBM_START (1 << 31)
> +#define PMC_PMBM_TIMEOUT (1 << 30)
> +#define PMC_PMBM_SLAVE_ERR (1 << 29)
> +#define PMC_PMBM_BUSY (1 << 28)
> +#define PMC_PMBM_READ (0 << 20)
> +#define PMC_PMBM_WRITE (1 << 20)
> +#define PMBM_WR_DATA 0x04
> +#define PMBM_TIMEOUT 0x08
> +#define PMBM_RD_DATA 0x0c
Can you re-use the definitions from include/linux/reset/bcm63xx_pmb.h,
you have the same constant names.
> +
> +#define BPCM_ID_REG 0x00
> +#define BPCM_CAPABILITIES 0x04
> +#define BPCM_CONTROL 0x08
> +#define BPCM_STATUS 0x0c
> +#define BPCM_ROSC_CONTROL 0x10
> +#define BPCM_ROSC_THRESH_H 0x14
> +#define BPCM_ROSC_THRESHOLD_BCM6838 0x14
> +#define BPCM_ROSC_THRESH_S 0x18
> +#define BPCM_ROSC_COUNT_BCM6838 0x18
> +#define BPCM_ROSC_COUNT 0x1c
> +#define BPCM_PWD_CONTROL_BCM6838 0x1c
> +#define BPCM_PWD_CONTROL 0x20
> +#define BPCM_SR_CONTROL_BCM6838 0x20
> +#define BPCM_PWD_ACCUM_CONTROL 0x24
> +#define BPCM_SR_CONTROL 0x28
> +#define BPCM_GLOBAL_CONTROL 0x2c
> +#define BPCM_MISC_CONTROL 0x30
> +#define BPCM_MISC_CONTROL2 0x34
> +#define BPCM_SGPHY_CNTL 0x38
> +#define BPCM_SGPHY_STATUS 0x3c
> +#define BPCM_ZONE0 0x40
> +#define BPCM_ZONE_CONTROL 0x00
> +#define BPCM_ZONE_CONFIG1 0x04
> +#define BPCM_ZONE_CONFIG2 0x08
> +#define BPCM_ZONE_FREQ_SCALAR_CONTROL 0x0c
> +#define BPCM_ZONE_SIZE 0x10
> +
> +enum brcm_pmc_chipset {
> + BCM4908,
> + BCM6848,
> + BCM6858,
> +};
> +
> +struct brcm_pmc_data {
> + enum brcm_pmc_chipset chipset;
> + int misc_strap_bus_reg;
> + int misc_strap_bus_pmc_rom_boot_bit;
> +};
> +
> +static const struct brcm_pmc_data brcm_pmc_4908_data = {
> + .chipset = BCM4908,
> + .misc_strap_bus_reg = 0x00,
> + .misc_strap_bus_pmc_rom_boot_bit = BIT(11),
> +};
> +
> +union bpcm_capabilities {
> + struct {
> + int num_zones:8;
> + int sr_reg_bits:8;
> + int pllType:2;
> + int reserved0:1;
> + int ubus:1;
> + int reserved1:12;
> + } bits;
> + u32 raw32;
> +} __attribute__((__packed__));
This is not going to work well if we extend this driver to support the
BCM63xx DSL SoCs which are done by the same engineering group within
Broadcom. Can you convert that to bits/masks instead such that this
becomes endian independent?
> +
> +union bpcm_zone_control {
> + struct {
> + u32 manual_clk_en:1;
> + u32 manual_reset_ctl:1;
> + u32 freq_scale_used:1; /* R/O */
> + u32 dpg_capable:1; /* R/O */
> + u32 manual_mem_pwr:2;
> + u32 manual_iso_ctl:1;
> + u32 manual_ctl:1;
> + u32 dpg_ctl_en:1;
> + u32 pwr_dn_req:1;
> + u32 pwr_up_req:1;
> + u32 mem_pwr_ctl_en:1;
> + u32 blk_reset_assert:1;
> + u32 mem_stby:1;
> + u32 reserved:5;
> + u32 pwr_cntl_state:5;
> + u32 freq_scalar_dyn_sel:1; /* R/O */
> + u32 pwr_off_state:1; /* R/O */
> + u32 pwr_on_state:1; /* R/O */
> + u32 pwr_good:1; /* R/O */
> + u32 dpg_pwr_state:1; /* R/O */
> + u32 mem_pwr_state:1; /* R/O */
> + u32 iso_state:1; /* R/O */
> + u32 reset_state:1; /* R/O */
> + } bits;
> + u32 raw32;
> +} __attribute__((__packed__));
> +
> +struct brcm_pmc {
> + const struct brcm_pmc_data *data;
> + void __iomem *base;
> + struct regmap *misc;
> + struct regmap *procmon;
> + struct device *dev;
> + struct reset_controller_dev rcdev;
> + bool direct;
> + bool little_endian;
> +};
> +
> +static DEFINE_SPINLOCK(lock);
You have a platform device, can you store the lock there instead of
having a global?
> +
> +#define cpu_to_dev32(pmc, val) \
> + ((pmc)->little_endian ? cpu_to_le32(val) : cpu_to_be32(val))
This would probably be better written as a static inline helper, and
maybe something like this:
static inline u32 brcm_pmc_readl(struct brcm_pmc *pmc, u8 offset)
{
if (pmc->little_endian)
return ioread32(pmc->base + offset);
else
return ioread32_be(pmc->base + offset);
}
> +
> +#define dev32_to_cpu(pmc, val) \
> + ((pmc)->little_endian ? le32_to_cpu(val) : be32_to_cpu(val))
> +
> +static int brcm_pmc_bpcm_wait(struct brcm_pmc *pmc, int bus)
> +{
> + unsigned long deadline = jiffies + usecs_to_jiffies(1000);
> + int pmbm = PROCMON_PMBM + bus * PROCMON_PMBM_SIZE;
> + u32 val;
> +
> + do {
> + regmap_read(pmc->procmon, pmbm + PMBM_CTRL, &val);
> + if (!(val & PMC_PMBM_START))
> + return 0;
> + cpu_relax();
> + udelay(10);
> + } while (!time_after_eq(jiffies, deadline));
> +
> + dev_err(pmc->dev, "Timeout waiting for the BPCM\n");
Can you use include/linux/reset/bcm63xx_pmb.h again here and check
arch/arm/mach-bcm/bcm63xx_pmb.c for how it is used.
> +
> + return -EBUSY;
> +}
> +
> +static int brcm_pmc_bpcm_read(struct brcm_pmc *pmc, u16 addr, int word_offset, u32 *val)
> +{
> + int err = 0;
> +
> + if (!pmc->direct) {
> + err = -EOPNOTSUPP;
Do an early return here so you don't have to indent the block under by
one tab.
> + } else {
> + u8 device = addr & 0xff;
> + u8 bus = addr >> 8;
> + unsigned long flags;
> + int pmbm;
> + u32 tmp;
> +
> + pmbm = PROCMON_PMBM + bus * PROCMON_PMBM_SIZE;
> +
> + spin_lock_irqsave(&lock, flags);
> +
> + /* TODO: Make sure PMBM is not busy */
> +
> + regmap_write(pmc->procmon, pmbm + PMBM_CTRL,
> + PMC_PMBM_START | PMC_PMBM_READ | (device << 12) | word_offset);
> +
> + err = brcm_pmc_bpcm_wait(pmc, bus);
> + if (!err)
> + err = regmap_read(pmc->procmon, pmbm + PMBM_RD_DATA, val);
> +
> + spin_unlock_irqrestore(&lock, flags);
> + }
> +
> + return err;
> +}
> +
> +static int brcm_pmc_bpcm_write(struct brcm_pmc *pmc, u16 addr, int word_offset, u32 val)
> +{
> + int err = 0;
> +
> + if (!pmc->direct) {
> + err = -EOPNOTSUPP;
Likewise.
[snip]
> +static int brcm_pmc_reset_xlate(struct reset_controller_dev *rcdev,
> + const struct of_phandle_args *reset_spec)
> +{
> + u8 device = reset_spec->args[1];
> + u8 bus = reset_spec->args[0];
> +
> + if (bus > 1)
> + return -EINVAL;
> +
> + return (bus << 8) | device;
IIRC the bus is limited to 8 bits, and the device ID certainly is
limited to 8 bits so you need to validate that before doing the
assignment otherwise you are going to see truncated values which could
be wrapped around and return some bogus reset ID combination.
You are using the same binding as
Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt, so maybe
you can add that compatible string into your binding document and
deprecate this old binding file.
Other than those, this looks great to me, thanks!
--
Florian
