Re: [PATCH v5 0/4] DCMI BT656 parallel bus mode support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Nov 09, 2020 at 09:37:51AM +0100, Alexandre Torgue wrote:
> Hi Sakari
> 
> On 11/6/20 12:53 PM, Sakari Ailus wrote:
> > Hi Alexandre,
> > 
> > On Thu, Nov 05, 2020 at 10:26:37AM +0100, Alexandre Torgue wrote:
> > > Hi Huges
> > > 
> > > On 11/4/20 6:32 PM, Hugues Fruchet wrote:
> > > > Add support of BT656 embedded synchronization bus.
> > > > This mode allows to save hardware synchro lines hsync & vsync
> > > > by replacing them with synchro codes embedded in data stream.
> > > > Add "bus-type" property and make it required so that there is no
> > > > ambiguity between parallel mode (bus-type=5) and BT656 mode (bus-type=6).
> > > > 
> > > > ===========
> > > > = history =
> > > > ===========
> > > > version 5:
> > > >     - Add revisited bindings and devicetree with explicit use of "bus-type"
> > > > 
> > > > version 4:
> > > >     - Fix typo in commit message
> > > > 
> > > > version 3:
> > > >     - Fix bus_width print to %u as per Sakari comment
> > > > 
> > > > version 2:
> > > >     - As per Sakari remark, revisit commit message and document
> > > >       BT656 parallel bus mode in bindings
> > > > 
> > > > version 1:
> > > >     - Initial submission
> > > > 
> > > > Hugues Fruchet (4):
> > > >     media: stm32-dcmi: add support of BT656 bus
> > > >     media: dt-bindings: media: st,stm32-dcmi: add support of BT656 bus
> > > >     ARM: dts: stm32: set bus-type in DCMI endpoint for stm32mp157c-ev1
> > > >       board
> > > >     ARM: dts: stm32: set bus-type in DCMI endpoint for stm32429i-eval
> > > >       board
> > > > 
> > > >    .../devicetree/bindings/media/st,stm32-dcmi.yaml   | 38 ++++++++++++++++++++++
> > > >    arch/arm/boot/dts/stm32429i-eval.dts               |  1 +
> > > >    arch/arm/boot/dts/stm32mp157c-ev1.dts              |  1 +
> > > >    drivers/media/platform/stm32/stm32-dcmi.c          | 37 +++++++++++++++++++--
> > > >    4 files changed, 75 insertions(+), 2 deletions(-)
> > > > 
> > > 
> > > I'll take DT patches on stm32-next tree.
> > 
> > Just checking: that is only the two last patches in the set, or also the
> > binding patch?
> 
> Usually I let drivers/subsystem maintainer taking dt-bindings patches with
> drivers patches.
> (If binding changes come only with dts(i) patches I take them in my tree)
> 
> -->So yes I'll take only the last two patches.

Ack, thanks!

-- 
Sakari Ailus



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux