Hi, On Tue, Nov 3, 2020 at 10:38 AM Matthias Kaehlcke <mka@xxxxxxxxxxxx> wrote: > > The trogdor design has two options for supplying the pp3300_hub power rail, > it can be supplied by pp3300_l7c or pp3300_a. Initially pp3300_l7c was > used, newer revisions (will) use pp3300_a as supply. > > Add a DT node for the pp3300_a path which includes a power switch that is > controlled by a GPIO. Make this path the default and keep trogdor rev1, > lazor rev0 and rev1 on pp3300_l7c. It might not hurt to mention that even on early hardware that GPIO84 was allocated to this purpose but that it was a stuff option for what actually provided power to the hub. This explains why it's OK to add the fixed regulator (just with no clients) even on old hardware. If GPIO84 had been used for something else on old hardware this would have been bad. > diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi > index bf875589d364..2d64e75a2d6d 100644 > --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi > @@ -174,6 +174,21 @@ pp3300_fp_tp: pp3300-fp-tp-regulator { > vin-supply = <&pp3300_a>; > }; > > + pp3300_hub: pp3300-hub { > + compatible = "regulator-fixed"; > + regulator-name = "pp3300_hub"; > + > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + pinctrl-names = "default"; > + pinctrl-0 = <&en_pp3300_hub>; > + > + vin-supply = <&pp3300_a>; You're leaving things in a bit of an inconsistent state here. The "pp3300_hub_7c" is always_on / boot_on. This new one isn't. I know this is slightly more complicated due to the fact that downstream we have a way to control the hub power but didn't quite get that resolved upstream, but the way you have it now, on new hardware upstream will power off the hub but also keep "pp3300_hub_7c" powered on for no reason. Seems like that should be fixed? > + }; > + > /* BOARD-SPECIFIC TOP LEVEL NODES */ > > backlight: backlight { > @@ -469,7 +484,7 @@ ppvar_l6c: ldo6 { > regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > }; > > - pp3300_hub: > + pp3300_hub_7c: nit: If it were me, I probably wouldn't have bothered introducing the "pp3300_hub_7c" alias since it's not a real thing in the schematic. I would have just had the older revisions refer to "pp3300_l7c". If you really love the "pp3300_hub_7c", though, I won't stand in your way. > pp3300_l7c: ldo7 { > regulator-min-microvolt = <3304000>; > regulator-max-microvolt = <3304000>; > @@ -1151,6 +1166,19 @@ pinconf { > }; > }; > > + en_pp3300_hub: en-pp3300-hub { > + pinmux { > + pins = "gpio84"; > + function = "gpio"; > + }; > + > + pinconf { > + pins = "gpio84"; > + drive-strength = <2>; > + bias-disable; > + }; > + }; > + > en_pp3300_dx_edp: en-pp3300-dx-edp { "hub" sorts after "dx", so the ordering is slightly wrong here. -Doug