From: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> Simple conversion using the new iio-consumers.yaml binding in the dt-schema. Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> Cc: Linus Walleij <linus.walleij@xxxxxxxxxx> --- .../bindings/iio/light/capella,cm3605.yaml | 78 +++++++++++++++++++ .../devicetree/bindings/iio/light/cm3605.txt | 41 ---------- 2 files changed, 78 insertions(+), 41 deletions(-) diff --git a/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml b/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml new file mode 100644 index 000000000000..001c99dbd14e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/capella,cm3605.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/capella,cm3605.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: + Capella Microsystems CM3605 Ambient Light and Short Distance Proximity Sensor + +maintainers: + - Linus Walleij <linus.walleij@xxxxxxxxxx> + +description: | + The CM3605 is an entirely analog part. However, it requires quite a bit of + software logic to interface a host operating system. + + This ALS and proximity sensor was one of the very first deployed in mobile + handsets, notably it is used in the very first Nexus One Android phone from + 2010. + +properties: + compatible: + const: capella,cm3605 + + aset-gpios: + maxItems: 1 + description: + ASET line (drive low to activate the ALS, should be flagged + GPIO_ACTIVE_LOW) + + interrupts: + maxItems: 1 + description: + Connected to the POUT (proximity sensor out) line. The edge + detection must be set to IRQ_TYPE_EDGE_BOTH so as to detect + movements toward and away from the proximity sensor. + + io-channels: + maxItems: 1 + description: + ADC channel used for converting the voltage from AOUT to a digital + representation. + + io-channel-names: + const: aout + + vdd-supply: true + + capella,aset-resistance-ohms: + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [50000, 100000, 300000, 600000] + description: > + Sensitivity calibration resistance. Note that calibration curves + are only provided for specific allowed values. Default: 100 kOhms. + +required: + - compatible + - aset-gpios + - interrupts + - io-channels + - io-channel-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + light-sensor { + compatible = "capella,cm3605"; + vdd-supply = <&foo_reg>; + aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>; + capella,aset-resistance-ohms = <100000>; + interrupts = <1 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&adc 0x01>; + io-channel-names = "aout"; + }; +... diff --git a/Documentation/devicetree/bindings/iio/light/cm3605.txt b/Documentation/devicetree/bindings/iio/light/cm3605.txt deleted file mode 100644 index 56331a79f9ab..000000000000 --- a/Documentation/devicetree/bindings/iio/light/cm3605.txt +++ /dev/null @@ -1,41 +0,0 @@ -Capella Microsystems CM3605 -Ambient Light and Short Distance Proximity Sensor - -The CM3605 is an entirely analog part which however require quite a bit of -software logic to interface a host operating system. - -This ALS and proximity sensor was one of the very first deployed in mobile -handsets, notably it is used in the very first Nexus One Android phone from -2010. - -Required properties: -- compatible: must be: "capella,cm3605" -- aset-gpios: GPIO line controlling the ASET line (drive low - to activate the ALS, should be flagged GPIO_ACTIVE_LOW) -- interrupts: the IRQ line (such as a GPIO) that is connected to - the POUT (proximity sensor out) line. The edge detection must - be set to IRQ_TYPE_EDGE_BOTH so as to detect movements toward - and away from the proximity sensor. -- io-channels: the ADC channel used for converting the voltage from - AOUT to a digital representation. -- io-channel-names: must be "aout" - -Optional properties: -- vdd-supply: regulator supplying VDD power to the component. -- capella,aset-resistance-ohms: the sensitivity calibration resistance, - in Ohms. Valid values are: 50000, 100000, 300000 and 600000, - as these are the resistance values that we are supplied with - calibration curves for. If not supplied, 100 kOhm will be assumed - but it is strongly recommended to supply this. - -Example: - -cm3605 { - compatible = "capella,cm3605"; - vdd-supply = <&foo_reg>; - aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>; - capella,aset-resistance-ohms = <100000>; - interrupts = <1 IRQ_TYPE_EDGE_BOTH>; - io-channels = <&adc 0x01>; - io-channel-names = "aout"; -}; -- 2.28.0
