On Wed, Oct 14, 2020 at 01:48:00PM +0200, Tomasz Figa wrote: > On Wed, Oct 14, 2020 at 10:31 AM Sakari Ailus > <sakari.ailus@xxxxxxxxxxxxxxx> wrote: > > > > On Wed, Oct 14, 2020 at 10:10:18AM +0800, Dongchun Zhu wrote: > > > Hello Sakari, > > > > > > Thanks for your timely review. > > > > > > On Tue, 2020-10-13 at 19:19 +0300, Sakari Ailus wrote: > > > > Hi Dongchun, > > > > > > > > On Tue, Oct 13, 2020 at 09:05:02PM +0800, Dongchun Zhu wrote: > > > > > Add YAML device tree binding for OV02A10 CMOS image sensor, and the > > > > > relevant MAINTAINERS entries. > > > > > > > > > > Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > > > > --- > > > > > .../bindings/media/i2c/ovti,ov02a10.yaml | 162 +++++++++++++++++++++ > > > > > MAINTAINERS | 7 + > > > > > 2 files changed, 169 insertions(+) > > > > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > > > > > > > > > [snip]... > > > > > > > > + ovti,mipi-clock-voltage: > > > > > + description: > > > > > + An array of 2-tuples items, and each item consists of link frequency and > > > > > + MIPI clock voltage unit like <freq-kHz volt-unit>. Clock voltage unit is > > > > > + dependent upon link speed, indicating MIPI transmission speed select that > > > > > + controls D-PHY timing setting by adjusting MIPI clock voltage to improve > > > > > + the clock driver capability. > > > > > + $ref: "/schemas/types.yaml#/definitions/uint32-array" > > > > > + minItems: 2 > > > > > + default: [390000, 4] > > > > > > > > Why do you have the link frequency here as well? > > > > > > > > In principle this does belong to the endpoint as link frequencies are > > > > specific to that, but I don't mind; there's just a single port anyway. > > > > > > > > > > This is an optional property which we model as an array of <link speed, > > > clock voltage> pairs. An example to have all link speeds up to 390MHz > > > use the value 4 for current driver. If one wants to select different > > > voltage for different link, they could do so as well. > > > > If you think you'd need that, then you need to put this to the endpoint. > > The mipi-clock-voltage property is not a property of the endpoint. The > link frequency there does not set the link frequency - it only > specifies which link frequency the given voltage should be used for. If it is not bound to the endpoint --- that specifies the properties of the link --- then you could just put it to the driver, couldn't you? But earlier on, we established that this is specific to a given board, or a given link. Endpoints are used to describe connections that a device may have to other devices. Therefore their properties are different. The graph bindings allow for several endpoints on a single physical port, some may be disabled in that case. This is admittedly mostly done with CSI-2 receivers. Either way, putting this property to the device may affect how DT source is arranged for boards that have this device. Any similar configuration on other devices with multiple transmitters or receivers would be in endpoints anyway --- because they have to, so I don't see why bindings for this device should be different. If you put it to endpoint, the driver also doesn't need to match the link frequencies in kHz and Hz between the two properties, but just use the same index for both. -- Sakari Ailus
