Van der Laan LANMCU is a module for the food storage rooms to control proper gas composition. Co-Developed-by: Robin van der Gracht <robin@xxxxxxxxxxx> Signed-off-by: Robin van der Gracht <robin@xxxxxxxxxxx> Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-lanmcu.dts | 469 ++++++++++++++++++++++++++++ 2 files changed, 470 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-lanmcu.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 2289a28c0ff6..dc2543a7b7e9 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -447,6 +447,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-icore.dtb \ imx6dl-icore-mipi.dtb \ imx6dl-icore-rqs.dtb \ + imx6dl-lanmcu.dtb \ imx6dl-mamoj.dtb \ imx6dl-nit6xlite.dtb \ imx6dl-nitrogen6x.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-lanmcu.dts b/arch/arm/boot/dts/imx6dl-lanmcu.dts new file mode 100644 index 000000000000..36c029dcc832 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-lanmcu.dts @@ -0,0 +1,469 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (c) 2019 Protonic Holland + * Copyright (c) 2020 Oleksij Rempel <kernel@xxxxxxxxxxxxxx>, Pengutronix + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include "imx6dl.dtsi" + +/ { + model = "Van der Laan LANMCU"; + compatible = "vdl,lanmcu", "fsl,imx6dl"; + + chosen { + stdout-path = &uart4; + }; + + clock_ksz8081: clock-ksz8081 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000 0>; + brightness-levels = <0 1000>; + num-interpolated-steps = <20>; + default-brightness-level = <19>; + }; + + display { + compatible = "fsl,imx-parallel-display"; + pinctrl-0 = <&pinctrl_ipu1_disp>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + display_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-debug { + function = LED_FUNCTION_STATUS; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + panel { + compatible = "edt,etm0700g0bdh6"; + backlight = <&backlight>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + + reg_otg_vbus: regulator-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "otg-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + usdhc2_wifi_pwrseq: usdhc2-wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wifi_npd>; + reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; + }; + +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rmii"; + clocks = <&clks IMX6QDL_CLK_ENET>, + <&clks IMX6QDL_CLK_ENET>, + <&clock_ksz8081>; + clock-names = "ipg", "ahb", "ptp"; + phy-handle = <&rgmii_phy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ8081RNA PHY */ + rgmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <300>; + }; + }; +}; + +&gpio1 { + gpio-line-names = + "", "SD1_CD", "", "", "", "", "", "", + "DEBUG_0", "BL_PWM", "", "", "", "", "", "", + "", "", "", "", "", "", "", "ENET_LED_GREEN", + "", "", "", "", "", "", "", ""; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "TS_INT", "USB_OTG1_OC", "USB_OTG1_PWR", "", + "", "", "", "", "UART2_CTS", "", "UART3_CTS", ""; +}; + +&gpio5 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "ENET_RST", "ENET_INT", + "", "", "I2C1_SDA", "I2C1_SCL", "", "", "", ""; +}; + +&gpio6 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "WLAN_REG_ON", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio7 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "EMMC_RST", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + /* additional i2c devices are added automatically by the boot loader */ +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ts_edt>; + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>; + + touchscreen-size-x = <1792>; + touchscreen-size-y = <1024>; + + touchscreen-fuzz-x = <0>; + touchscreen-fuzz-y = <0>; + + /* Touch screen calibration */ + threshold = <50>; + gain = <5>; + offset = <10>; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&ipu1_di0_disp0 { + remote-endpoint = <&display_in>; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + linux,rs485-enabled-at-boot-time; + uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + linux,rs485-enabled-at-boot-time; + uart-has-rtscts; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + phy_type = "utmi"; + dr_mode = "host"; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + no-1-8-v; + disable-wp; + cap-sd-highspeed; + no-mmc; + no-sdio; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + no-1-8-v; + non-removable; + mmc-pwrseq = <&usdhc2_wifi_pwrseq>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + no-1-8-v; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&iomuxc { + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000 + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + /* MX6QDL_ENET_PINGRP4 */ + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0 + /* nINTRP */ + MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_ipu1_disp: ipudisp1grp { + fsl,pins = < + /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */ + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8 + >; + }; + + pinctrl_ts_edt: ts1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x130b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x130b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 + >; + }; + + pinctrl_wifi_npd: wifinpd { + fsl,pins = < + /* WL_REG_ON */ + MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069 + >; + }; +}; -- 2.28.0