Hi Marco,
thank you for review!
On Wed, Oct 14, 2020 at 12:05:01PM +0200, Marco Felsch wrote:
> Hi Oleksij,
>
> pls can you send a patch adding this board to:
> Documentation/devicetree/bindings/arm/fsl.yaml
>
> infront of this patch?
This is patch 3/3 and fsl.yaml 2/3. Do I'm missing some thing?
> On 20-10-14 10:53, Oleksij Rempel wrote:
> > Van der Laan LANMCU is a module for the food storage rooms to control
> > proper gas composition.
> >
> > Co-Developed-by: Robin van der Gracht <robin@xxxxxxxxxxx>
> > Signed-off-by: Robin van der Gracht <robin@xxxxxxxxxxx>
> > Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
> > ---
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/imx6dl-lanmcu.dts | 468 ++++++++++++++++++++++++++++
> > 2 files changed, 469 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6dl-lanmcu.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 2289a28c0ff6..dc2543a7b7e9 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -447,6 +447,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6dl-icore.dtb \
> > imx6dl-icore-mipi.dtb \
> > imx6dl-icore-rqs.dtb \
> > + imx6dl-lanmcu.dtb \
> > imx6dl-mamoj.dtb \
> > imx6dl-nit6xlite.dtb \
> > imx6dl-nitrogen6x.dtb \
> > diff --git a/arch/arm/boot/dts/imx6dl-lanmcu.dts b/arch/arm/boot/dts/imx6dl-lanmcu.dts
> > new file mode 100644
> > index 000000000000..60336c972286
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6dl-lanmcu.dts
> > @@ -0,0 +1,468 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Copyright (c) 2019 Protonic Holland
> > + * Copyright (c) 2020 Oleksij Rempel <kernel@xxxxxxxxxxxxxx>, Pengutronix
> > + */
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/leds/common.h>
> > +#include "imx6dl.dtsi"
> > +
> > +/ {
>
> ...
>
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rmii";
> > + clocks = <&clks IMX6QDL_CLK_ENET>,
> > + <&clks IMX6QDL_CLK_ENET>,
> > + <&clock_ksz8081>;
> > + clock-names = "ipg", "ahb", "ptp";
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + /* Microchip KSZ8081RNA PHY */
> > + rgmii_phy: ethernet-phy@0 {
>
> Do you need this phandle here?
Fixed by adding phy-handle.
> > + reg = <0>;
> > + interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
> > + reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
> > + reset-assert-us = <10000>;
> > + reset-deassert-us = <300>;
> > + };
> > + };
> > +};
>
> ...
>
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + edt-ft5406@38 {
>
> Please use generic names like: touchscreen@38 or touchcontroller@38.
OK, i'll use "touchscreen@38".
touchcontroller@ this variant was never used in the mainline kernel.
> > + compatible = "edt,edt-ft5406";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ts_edt>;
> > + reg = <0x38>;
>
> reg should be 2nd entry.
done
> > + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> > +
> > + touchscreen-size-x = <1792>;
> > + touchscreen-size-y = <1024>;
> > +
> > + touchscreen-fuzz-x = <0>;
> > + touchscreen-fuzz-y = <0>;
> > +
> > + /* Touch screen calibration */
> > + threshold = <50>;
> > + gain = <5>;
> > + offset = <10>;
> > + };
> > +
> > + rtc@51 {
> > + compatible = "nxp,pcf8563";
> > + reg = <0x51>;
> > + };
> > +};
>
> ...
>
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + no-1-8-v;
> > + non-removable;
> > + mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
> > + status = "okay";
>
> status is always the last property of this list.
done
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + brcmf: bcrmf@1 {
> > + reg = <1>;
> > + compatible = "brcm,bcm4329-fmac";
> > + };
> > +};
>
Regards,
Oleksij
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
