Hi Oleksij,
pls can you send a patch adding this board to:
Documentation/devicetree/bindings/arm/fsl.yaml
infront of this patch?
On 20-10-14 10:53, Oleksij Rempel wrote:
> Van der Laan LANMCU is a module for the food storage rooms to control
> proper gas composition.
>
> Co-Developed-by: Robin van der Gracht <robin@xxxxxxxxxxx>
> Signed-off-by: Robin van der Gracht <robin@xxxxxxxxxxx>
> Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-lanmcu.dts | 468 ++++++++++++++++++++++++++++
> 2 files changed, 469 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-lanmcu.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 2289a28c0ff6..dc2543a7b7e9 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -447,6 +447,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6dl-icore.dtb \
> imx6dl-icore-mipi.dtb \
> imx6dl-icore-rqs.dtb \
> + imx6dl-lanmcu.dtb \
> imx6dl-mamoj.dtb \
> imx6dl-nit6xlite.dtb \
> imx6dl-nitrogen6x.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-lanmcu.dts b/arch/arm/boot/dts/imx6dl-lanmcu.dts
> new file mode 100644
> index 000000000000..60336c972286
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-lanmcu.dts
> @@ -0,0 +1,468 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Copyright (c) 2019 Protonic Holland
> + * Copyright (c) 2020 Oleksij Rempel <kernel@xxxxxxxxxxxxxx>, Pengutronix
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include "imx6dl.dtsi"
> +
> +/ {
...
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rmii";
> + clocks = <&clks IMX6QDL_CLK_ENET>,
> + <&clks IMX6QDL_CLK_ENET>,
> + <&clock_ksz8081>;
> + clock-names = "ipg", "ahb", "ptp";
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* Microchip KSZ8081RNA PHY */
> + rgmii_phy: ethernet-phy@0 {
Do you need this phandle here?
> + reg = <0>;
> + interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
> + reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <10000>;
> + reset-deassert-us = <300>;
> + };
> + };
> +};
...
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + edt-ft5406@38 {
Please use generic names like: touchscreen@38 or touchcontroller@38.
> + compatible = "edt,edt-ft5406";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ts_edt>;
> + reg = <0x38>;
reg should be 2nd entry.
> + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> +
> + touchscreen-size-x = <1792>;
> + touchscreen-size-y = <1024>;
> +
> + touchscreen-fuzz-x = <0>;
> + touchscreen-fuzz-y = <0>;
> +
> + /* Touch screen calibration */
> + threshold = <50>;
> + gain = <5>;
> + offset = <10>;
> + };
> +
> + rtc@51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + };
> +};
...
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + no-1-8-v;
> + non-removable;
> + mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
> + status = "okay";
status is always the last property of this list.
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + brcmf: bcrmf@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + };
> +};
Regards,
Marco
