On Thu, Oct 08, 2020 at 03:05:13PM +0200, Lars Povlsen wrote: > This adds DT bindings for the Microsemi/Microchip SGPIO controller, > bindings microchip,sparx5-sgpio, mscc,ocelot-sgpio and > mscc,luton-sgpio. > > Signed-off-by: Lars Povlsen <lars.povlsen@xxxxxxxxxxxxx> > --- > .../pinctrl/microchip,sparx5-sgpio.yaml | 140 ++++++++++++++++++ > 1 file changed, 140 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml > > diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml > new file mode 100644 > index 000000000000..fc41495800ed > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml > @@ -0,0 +1,140 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pinctrl/microchip,sparx5-sgpio.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Microsemi/Microchip Serial GPIO controller > + > +maintainers: > + - Lars Povlsen <lars.povlsen@xxxxxxxxxxxxx> > + > +description: | > + By using a serial interface, the SIO controller significantly extend > + the number of available GPIOs with a minimum number of additional > + pins on the device. The primary purpose of the SIO controllers is to > + connect control signals from SFP modules and to act as an LED > + controller. > + > +properties: > + $nodename: > + pattern: "^gpio@[0-9a-f]+$" > + > + compatible: > + enum: > + - microchip,sparx5-sgpio > + - mscc,ocelot-sgpio > + - mscc,luton-sgpio > + > + "#address-cells": > + const: 1 > + > + "#size-cells": > + const: 0 > + > + reg: > + maxItems: 1 > + > + clocks: > + maxItems: 1 > + > + microchip,sgpio-port-ranges: > + description: This is a sequence of tuples, defining intervals of > + enabled ports in the serial input stream. The enabled ports must > + match the hardware configuration in order for signals to be > + properly written/read to/from the controller holding > + registers. Being tuples, then number of arguments must be > + even. The tuples mast be ordered (low, high) and are > + inclusive. > + $ref: /schemas/types.yaml#/definitions/uint32-matrix > + items: > + items: > + - description: | > + "low" indicates start bit number of range > + minimum: 0 > + maximum: 31 > + - description: | > + "high" indicates end bit number of range > + minimum: 0 > + maximum: 31 > + minItems: 1 > + maxItems: 32 > + > + microchip,sgpio-frequency: > + description: The sgpio controller frequency (Hz). This dictates > + the serial bitstream speed, which again affects the latency in > + getting control signals back and forth between external shift > + registers. The speed must be no larger than half the system > + clock, and larger than zero. > + $ref: /schemas/types.yaml#/definitions/uint32 Perhaps use 'bus-frequency' here. If not, needs unit suffix. Either way, you can drop the type in those cases. With that, Reviewed-by: Rob Herring <robh@xxxxxxxxxx> > + minimum: 1 > + default: 12500000 > + > +patternProperties: > + "^gpio@[0-1]$": > + type: object > + properties: > + compatible: > + const: microchip,sparx5-sgpio-bank > + > + reg: > + description: | > + The GPIO bank number. "0" is designates the input pin bank, > + "1" the output bank. > + maxItems: 1 > + > + gpio-controller: true > + > + '#gpio-cells': > + const: 3 > + > + ngpios: > + minimum: 1 > + maximum: 128 > + > + required: > + - compatible > + - reg > + - gpio-controller > + - '#gpio-cells' > + - ngpios > + > + additionalProperties: false > + > +additionalProperties: false > + > +required: > + - compatible > + - reg > + - clocks > + - microchip,sgpio-port-ranges > + - "#address-cells" > + - "#size-cells" > + > +examples: > + - | > + sgpio2: gpio@1101059c { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "microchip,sparx5-sgpio"; > + clocks = <&sys_clk>; > + pinctrl-0 = <&sgpio2_pins>; > + pinctrl-names = "default"; > + reg = <0x1101059c 0x100>; > + microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>; > + microchip,sgpio-frequency = <25000000>; > + sgpio_in2: gpio@0 { > + reg = <0>; > + compatible = "microchip,sparx5-sgpio-bank"; > + gpio-controller; > + #gpio-cells = <3>; > + ngpios = <96>; > + }; > + sgpio_out2: gpio@1 { > + compatible = "microchip,sparx5-sgpio-bank"; > + reg = <1>; > + gpio-controller; > + #gpio-cells = <3>; > + ngpios = <96>; > + }; > + }; > -- > 2.25.1