On Wed, Sep 9, 2020 at 9:46 AM Manish Narani <MNARANI@xxxxxxxxxx> wrote: > > Hi Rob, > > Thanks for the review. > > > -----Original Message----- > > From: Rob Herring <robh@xxxxxxxxxx> > > Sent: Wednesday, September 9, 2020 4:35 AM > > To: Manish Narani <MNARANI@xxxxxxxxxx> > > Cc: gregkh@xxxxxxxxxxxxxxxxxxx; Michal Simek <michals@xxxxxxxxxx>; > > balbi@xxxxxxxxxx; p.zabel@xxxxxxxxxxxxxx; linux-usb@xxxxxxxxxxxxxxx; > > devicetree@xxxxxxxxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux- > > kernel@xxxxxxxxxxxxxxx; git <git@xxxxxxxxxx> > > Subject: Re: [PATCH 1/2] dt-bindings: usb: dwc3-xilinx: Add documentation for > > Versal DWC3 Controller > > > > On Thu, Aug 27, 2020 at 12:14:00AM +0530, Manish Narani wrote: > > > Add documentation for Versal DWC3 controller. Add required property > > > 'reg' for the same. Also add optional properties for snps,dwc3. > > > > > > Signed-off-by: Manish Narani <manish.narani@xxxxxxxxxx> > > > --- > > > .../devicetree/bindings/usb/dwc3-xilinx.txt | 12 +++++++++++- > > > 1 file changed, 11 insertions(+), 1 deletion(-) > > > > > > diff --git a/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt > > b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt > > > index 4aae5b2cef56..dd41ed831411 100644 > > > --- a/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt > > > +++ b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt > > > @@ -1,7 +1,8 @@ > > > Xilinx SuperSpeed DWC3 USB SoC controller > > > > > > Required properties: > > > -- compatible: Should contain "xlnx,zynqmp-dwc3" > > > +- compatible: May contain "xlnx,zynqmp-dwc3" or "xlnx,versal- > > dwc3" > > > +- reg: Base address and length of the register control block > > > - clocks: A list of phandles for the clocks listed in clock-names > > > - clock-names: Should contain the following: > > > "bus_clk" Master/Core clock, have to be >= 125 MHz for SS > > > @@ -13,12 +14,19 @@ Required child node: > > > A child node must exist to represent the core DWC3 IP block. The name of > > > the node is not important. The content of the node is defined in dwc3.txt. > > > > > > +Optional properties for snps,dwc3: > > > +- dma-coherent: Enable this flag if CCI is enabled in design. Adding this > > > + flag configures Global SoC bus Configuration Register and > > > + Xilinx USB 3.0 IP - USB coherency register to enable CCI. > > > +- interrupt-names: This property provides the names of the interrupt ids > > used > > > > You have to define what the names are. 'dwc_usb3' seems pretty pointless > > if only 1 name. > > OK. I am planning to add more interrupt ids going ahead. For now I will remove > this interrupt name in v2. The interrupt name will be added along with other interrupt > names. Define all the interrupts you have. Bindings should be complete, not what a driver for some OS happens to use at some point in time. Rob
