Hi Geert,
Thank you for the review.
On Thu, Sep 3, 2020 at 1:20 PM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
>
> Hi Prabhakar,
>
> On Tue, Aug 25, 2020 at 6:28 PM Lad Prabhakar
> <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> wrote:
> > Add support for LED trigger on SD2 interface.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > Reviewed-by: Chris Paterson <Chris.Paterson2@xxxxxxxxxxx>
>
> > --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts
> > +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts
> > @@ -63,6 +63,16 @@
> > enable-gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
> > };
> >
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + sdhi2_led {
> > + label = "sdio-led";
> > + gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
>
> GPIO_ACTIVE_HIGH?
>
I did try with GPIO_ACTIVE_HIGH and it didn't work as expected. To
make sure I can control the LED through sysfs I deleted the node from
DTS and exported the pin GP5_22 (858) and writing the value "out"
direction and setting the values 0/1 to value did not toggle the SDIO
LED as expected and it stayed OFF all the time.
Looks like there is some information missing in the schematics.
I did some experiments. I completely removed the SDHI, LED and
regulator nodes and booted the system and exported GP1_27 (989) and
wrote values 0/1 and this toggled the SDIO_LED.
U-boot sets the below, so in u-boot the SDIO_LED is ON:
gpio_direction_output(GPIO_GP_1_27, 0); /* power on */
gpio_set_value(GPIO_GP_1_27, 0);
gpio_direction_output(GPIO_GP_5_22, 0); /* LED */
gpio_set_value(GPIO_GP_5_22, 1);
gpio_direction_output(GPIO_GP_1_8, 0); /* 1: 3.3V, 0: 1.8V*/
gpio_set_value(GPIO_GP_1_8, 1);
So in comparison we would need a hog node as below (and with this the
LED triggers correctly as expected),
&gpio5 {
sdio-led-gpio {
gpio-hog;
gpios = <22 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "sdio-led-gpio";
};
};
Let me know if you are OK with the above.
Looks like the SDIO_PWR is tied up with an SDIO_LED pin and the
information is missing from schematics.
Cheers,
Prabhakar
> The LED is driven by an NPN transistor, with the LED between 3.3V and
> the transistor's collector.
>
> > + linux,default-trigger = "mmc1";
> > + };
> > + };
> > +
> > lvds-receiver {
> > compatible = "ti,ds90cf384a", "lvds-decoder";
> > vcc-supply = <&vcc_3v3_tft1>;
>
> With the above fixed:
> Reviewed-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
>
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
