On Mon, Jul 20, 2020 at 09:25:22PM -0700, Alexandru Stan wrote:
> After the "PWM backlight interpolation adjustments" patches, the
> backlight interpolation works a little differently. The way these
> dts files were working before was relying on a bug (IMHO).
>
> Remove the 0-3 range since otherwise we would have a 252 long
> interpolation that would slowly go between 0 and 3, looking really bad
> in userspace.
>
> We'll still have the 0% point available to userspace, "backlight:
> pwm_bl: Artificially add 0% during interpolation" takes care of that.
>
> Signed-off-by: Alexandru Stan <amstan@xxxxxxxxxxxx>
Hmnn... almost wish I hadn't seen this ;-)
This basically says that your first patch will produce some odd
behaviour for existing device trees! On the other hand I strongly
suspect this trick is only currently seen on Chromebooks (since IIRC
that's where backlight animation is popular).
To be clear I'm entirely in favour of the changes in this patch... I
just dubious about combining it with artifically adding that 0%
Daniel.
> ---
>
> arch/arm/boot/dts/rk3288-veyron-jaq.dts | 2 +-
> arch/arm/boot/dts/rk3288-veyron-minnie.dts | 2 +-
> arch/arm/boot/dts/rk3288-veyron-tiger.dts | 2 +-
> 3 files changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/boot/dts/rk3288-veyron-jaq.dts b/arch/arm/boot/dts/rk3288-veyron-jaq.dts
> index 171ba6185b6d..af4b21636c08 100644
> --- a/arch/arm/boot/dts/rk3288-veyron-jaq.dts
> +++ b/arch/arm/boot/dts/rk3288-veyron-jaq.dts
> @@ -20,7 +20,7 @@ / {
>
> &backlight {
> /* Jaq panel PWM must be >= 3%, so start non-zero brightness at 8 */
> - brightness-levels = <0 8 255>;
> + brightness-levels = <8 255>;
> num-interpolated-steps = <247>;
> };
>
> diff --git a/arch/arm/boot/dts/rk3288-veyron-minnie.dts b/arch/arm/boot/dts/rk3288-veyron-minnie.dts
> index 383fad1a88a1..b25aa2f3cbee 100644
> --- a/arch/arm/boot/dts/rk3288-veyron-minnie.dts
> +++ b/arch/arm/boot/dts/rk3288-veyron-minnie.dts
> @@ -39,7 +39,7 @@ volum_up {
>
> &backlight {
> /* Minnie panel PWM must be >= 1%, so start non-zero brightness at 3 */
> - brightness-levels = <0 3 255>;
> + brightness-levels = <3 255>;
> num-interpolated-steps = <252>;
> };
>
> diff --git a/arch/arm/boot/dts/rk3288-veyron-tiger.dts b/arch/arm/boot/dts/rk3288-veyron-tiger.dts
> index 069f0c2c1fdf..52a84cbe7a90 100644
> --- a/arch/arm/boot/dts/rk3288-veyron-tiger.dts
> +++ b/arch/arm/boot/dts/rk3288-veyron-tiger.dts
> @@ -23,7 +23,7 @@ / {
>
> &backlight {
> /* Tiger panel PWM must be >= 1%, so start non-zero brightness at 3 */
> - brightness-levels = <0 3 255>;
> + brightness-levels = <3 255>;
> num-interpolated-steps = <252>;
> };
>
> --
> 2.27.0
