The definition of "xxx-in-supply" was generic, thus define in detail the
possible cases for each chip variant.
While there also apply a few smaller improvements:
- document that the only possible I2C slave address is 0x60 as per the
datasheet and fix the second example accordingly
- remove "MFD driver" from the title as it is implementation specific
- replace "PMIC" with "buck converter" in title as it is more informative
Signed-off-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
---
Changes in v4:
- split in two different bindings (Rob)
- remove "MFD driver" from title as it is implementation specific; also
replace "PMIC" with "buck converter" which is more informative
Changes in v3:
- fix yaml errors
Changes in v2:
- this patch replaces patch "regulator: lp87565: dt: remove duplicated
section" in RFC,v1 (Rob Herring)
- use capital letters consistently (Lee Jones)
- replace "regulator" -> "mfd" in subject line (Lee Jones)
- replace "dt:" suffix with "dt-bindings:" prefix in subject line
---
.../devicetree/bindings/mfd/lp87565.txt | 79 -----------------
.../bindings/mfd/ti,lp87561-q1.yaml | 68 +++++++++++++++
.../bindings/mfd/ti,lp87565-q1.yaml | 85 +++++++++++++++++++
3 files changed, 153 insertions(+), 79 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/mfd/lp87565.txt
create mode 100644 Documentation/devicetree/bindings/mfd/ti,lp87561-q1.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/ti,lp87565-q1.yaml
diff --git a/Documentation/devicetree/bindings/mfd/lp87565.txt b/Documentation/devicetree/bindings/mfd/lp87565.txt
deleted file mode 100644
index 41671e0dc26b..000000000000
--- a/Documentation/devicetree/bindings/mfd/lp87565.txt
+++ /dev/null
@@ -1,79 +0,0 @@
-TI LP87565 PMIC MFD driver
-
-Required properties:
- - compatible: "ti,lp87565", "ti,lp87565-q1"
- - reg: I2C slave address.
- - gpio-controller: Marks the device node as a GPIO Controller.
- - #gpio-cells: Should be two. The first cell is the pin number and
- the second cell is used to specify flags.
- See ../gpio/gpio.txt for more information.
- - xxx-in-supply: Phandle to parent supply node of each regulator
- populated under regulators node. xxx should match
- the supply_name populated in driver.
-Example:
-
-lp87565_pmic: pmic@60 {
- compatible = "ti,lp87565-q1";
- reg = <0x60>;
- gpio-controller;
- #gpio-cells = <2>;
-
- buck10-in-supply = <&vsys_3v3>;
- buck23-in-supply = <&vsys_3v3>;
-
- regulators: regulators {
- buck10_reg: buck10 {
- /* VDD_MPU */
- regulator-name = "buck10";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck23_reg: buck23 {
- /* VDD_GPU */
- regulator-name = "buck23";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-boot-on;
- regulator-always-on;
- };
- };
-};
-
-TI LP87561 PMIC:
-
-This is a single output 4-phase regulator configuration
-
-Required properties:
- - compatible: "ti,lp87561-q1"
- - reg: I2C slave address.
- - gpio-controller: Marks the device node as a GPIO Controller.
- - #gpio-cells: Should be two. The first cell is the pin number and
- the second cell is used to specify flags.
- See ../gpio/gpio.txt for more information.
- - xxx-in-supply: Phandle to parent supply node of each regulator
- populated under regulators node. xxx should match
- the supply_name populated in driver.
-Example:
-
-lp87561_pmic: pmic@62 {
- compatible = "ti,lp87561-q1";
- reg = <0x62>;
- gpio-controller;
- #gpio-cells = <2>;
-
- buck3210-in-supply = <&vsys_3v3>;
-
- regulators: regulators {
- buck3210_reg: buck3210 {
- /* VDD_CORE */
- regulator-name = "buck3210";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <800000>;
- regulator-always-on;
- regulator-boot-on;
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/mfd/ti,lp87561-q1.yaml b/Documentation/devicetree/bindings/mfd/ti,lp87561-q1.yaml
new file mode 100644
index 000000000000..c0c56e9e5a06
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti,lp87561-q1.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ti,lp87561-q1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI LP87561-Q1 single 4-phase output buck converter
+
+maintainers:
+ - Keerthy <j-keerthy@xxxxxx>
+
+properties:
+ compatible:
+ const: ti,lp87561-q1
+
+ reg:
+ description: I2C slave address
+ const: 0x60
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ description:
+ The first cell is the pin number.
+ The second cell is is used to specify flags.
+ See ../gpio/gpio.txt for more information.
+ const: 2
+
+ buck3210-in-supply:
+ description:
+ Phandle to parent supply node for all the four BUCK converters.
+
+required:
+ - compatible
+ - reg
+ - gpio-controller
+ - '#gpio-cells'
+ - buck3210-in-supply
+
+examples:
+ - |
+ i2c@0 {
+ reg = <0x0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@60 {
+ compatible = "ti,lp87561-q1";
+ reg = <0x60>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck3210-in-supply = <&vsys_3v3>;
+
+ regulators {
+ buck3210_reg: buck3210 {
+ /* VDD_CORE */
+ regulator-name = "buck3210";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/mfd/ti,lp87565-q1.yaml b/Documentation/devicetree/bindings/mfd/ti,lp87565-q1.yaml
new file mode 100644
index 000000000000..1eafe0fb90cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti,lp87565-q1.yaml
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ti,lp87565-q1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI LP87565-Q1 / LP87565 dual 2-phase output buck converter
+
+maintainers:
+ - Keerthy <j-keerthy@xxxxxx>
+
+properties:
+ compatible:
+ oneOf:
+ - const: ti,lp87565
+ - const: ti,lp87565-q1
+
+ reg:
+ description: I2C slave address
+ const: 0x60
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ description:
+ The first cell is the pin number.
+ The second cell is is used to specify flags.
+ See ../gpio/gpio.txt for more information.
+ const: 2
+
+ buck10-in-supply:
+ description:
+ Phandle to parent supply node for BUCK0 and BUCK1 converters.
+
+ buck23-in-supply:
+ description:
+ Phandle to parent supply node for BUCK2 and BUCK3 converters.
+
+required:
+ - compatible
+ - reg
+ - gpio-controller
+ - '#gpio-cells'
+ - buck10-in-supply
+ - buck23-in-supply
+
+examples:
+ - |
+ i2c@0 {
+ reg = <0x0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@60 {
+ compatible = "ti,lp87565-q1";
+ reg = <0x60>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck10-in-supply = <&vsys_3v3>;
+ buck23-in-supply = <&vsys_3v3>;
+
+ regulators {
+ buck10_reg: buck10 {
+ /* VDD_MPU */
+ regulator-name = "buck10";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck23_reg: buck23 {
+ /* VDD_GPU */
+ regulator-name = "buck23";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+ };
+
+...
--
2.28.0
