Convert the i.MX uart binding to DT schema format using json-schema.
Signed-off-by: Anson Huang <Anson.Huang@xxxxxxx>
---
.../devicetree/bindings/serial/fsl-imx-uart.txt | 40 ----------
.../devicetree/bindings/serial/fsl-imx-uart.yaml | 92 ++++++++++++++++++++++
2 files changed, 92 insertions(+), 40 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
create mode 100644 Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
deleted file mode 100644
index 9582fc2..0000000
--- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
+++ /dev/null
@@ -1,40 +0,0 @@
-* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
-
-Required properties:
-- compatible : Should be "fsl,<soc>-uart"
-- reg : Address and length of the register set for the device
-- interrupts : Should contain uart interrupt
-
-Optional properties:
-- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
- in DCE mode by default.
-- fsl,inverted-tx , fsl,inverted-rx : Indicate that the hardware attached
- to the peripheral inverts the signal transmitted or received,
- respectively, and that the peripheral should invert its output/input
- using the INVT/INVR registers.
-- rs485-rts-delay, rs485-rts-active-low, rs485-rx-during-tx,
- linux,rs485-enabled-at-boot-time: see rs485.txt. Note that for RS485
- you must enable either the "uart-has-rtscts" or the "rts-gpios"
- properties. In case you use "uart-has-rtscts" the signal that controls
- the transceiver is actually CTS_B, not RTS_B. CTS_B is always output,
- and RTS_B is input, regardless of dte-mode.
-
-Please check Documentation/devicetree/bindings/serial/serial.yaml
-for the complete list of generic properties.
-
-Note: Each uart controller should have an alias correctly numbered
-in "aliases" node.
-
-Example:
-
-aliases {
- serial0 = &uart1;
-};
-
-uart1: serial@73fbc000 {
- compatible = "fsl,imx51-uart", "fsl,imx21-uart";
- reg = <0x73fbc000 0x4000>;
- interrupts = <31>;
- uart-has-rtscts;
- fsl,dte-mode;
-};
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml b/Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml
new file mode 100644
index 0000000..cba3f83
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml
@@ -0,0 +1,92 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
+
+maintainers:
+ - Fabio Estevam <fabio.estevam@xxxxxxx>
+
+allOf:
+ - $ref: "serial.yaml"
+ - $ref: "rs485.yaml"
+
+properties:
+ compatible:
+ oneOf:
+ - const: fsl,imx1-uart
+ - const: fsl,imx21-uart
+ - const: fsl,imx53-uart
+ - const: fsl,imx6q-uart
+ - items:
+ - enum:
+ - fsl,imx25-uart
+ - fsl,imx27-uart
+ - fsl,imx31-uart
+ - fsl,imx35-uart
+ - fsl,imx50-uart
+ - fsl,imx51-uart
+ - const: fsl,imx21-uart
+ - items:
+ - enum:
+ - fsl,imx6sl-uart
+ - fsl,imx6sll-uart
+ - fsl,imx6sx-uart
+ - fsl,imx6ul-uart
+ - fsl,imx7d-uart
+ - const: fsl,imx6q-uart
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ fsl,dte-mode:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ Indicate the uart works in DTE mode. The uart works in DCE mode by default.
+
+ fsl,inverted-tx:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ Indicate that the hardware attached to the peripheral inverts the signal
+ transmitted, and that the peripheral should invert its output using the
+ INVT registers.
+
+ fsl,inverted-rx:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: |
+ Indicate that the hardware attached to the peripheral inverts the signal
+ received, and that the peripheral should invert its input using the
+ INVR registers.
+
+ uart-has-rtscts: true
+
+ rs485-rts-delay: true
+ rs485-rts-active-low: true
+ rs485-rx-during-tx: true
+ linux,rs485-enabled-at-boot-time: true
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ aliases {
+ serial0 = &uart1;
+ };
+
+ uart1: serial@73fbc000 {
+ compatible = "fsl,imx51-uart", "fsl,imx21-uart";
+ reg = <0x73fbc000 0x4000>;
+ interrupts = <31>;
+ uart-has-rtscts;
+ fsl,dte-mode;
+ };
--
2.7.4
