Re: [PATCH 2/3] mfd: qcom-rpm: Driver for the Qualcomm RPM

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 






On 29/05/14 20:45, Bjorn Andersson wrote:
On Thu, May 29, 2014 at 9:19 AM, Srinivas Kandagatla
<srinivas.kandagatla@xxxxxxxxxx> wrote:
+++ b/drivers/mfd/qcom_rpm.c

the line spacing looks bit odd.


I'll fix

+};
+
+#define RPM_STATUS_REG(rpm, i) ((rpm)->status_regs + (i) * 4)
+#define RPM_CTRL_REG(rpm, i)   ((rpm)->ctrl_regs + (i) * 4)
+#define RPM_REQ_REG(rpm, i)    ((rpm)->req_regs + (i) * 4)


Probably you could make these macros bit more generic by removing the rpm
and let the calling code dereference it.



I first open coded them, I then had separate writel/readl wrappers for them and
then I settled for this, as I figured it help clarifying the code. I can have
another look at it, but I don't think that below will make things clearer.

#define RPM_IDX_2_OFFSET(i) ((i) * 4)


Yes, just leave it as it is.
[...]


+static int qcom_rpm_probe(struct platform_device *pdev)
+{
+       const struct of_device_id *match;
+       const struct qcom_rpm *template;
+       struct resource *res;
+       struct qcom_rpm *rpm;
+       u32 fw_version[3];
+       int irq_wakeup;
+       int irq_ack;
+       int irq_err;
+       int ret;
+
+       rpm = devm_kzalloc(&pdev->dev, sizeof(*rpm), GFP_KERNEL);


Sorry If I missed somthing obvious, But why not just use the structure from
of_data. Is the global structure going to be used for something else?

Or make a seperate structure for of_data and not use struct qcom_rpm?




Although we will not have more than one rpm in a system and therefore not
instatiate this driver multiple times I do not want to run it off the global
state.

I agree.

Why not make a separate data structure for the qcom_of_data?

+       if (!rpm) {
+               dev_err(&pdev->dev, "Can't allocate qcom_rpm\n");

message not necessary as kernel will print the alocation failures.


Thanks!

+               return -ENOMEM;
+       }

[...]

+
+       res = platform_get_resource(pdev, IORESOURCE_MEM, 0);

Should't you use the platform_get_resource_byname here?

missed error case checks too.


This is a fairly commonly used construct, to have the error from
platform_get_resource being propagated through devm_ioremap_resource and catch
it there. It gives an extra error print in the log, but I find it very clean.
Sorry I missed that point...


But my point on platform_get_resource_byname is to remove the dependency on the resource ordering, It is very difficult to catch errors resulting in wrong ordered resources in DT.


+       rpm->status_regs = devm_ioremap_resource(&pdev->dev, res);
+       rpm->ctrl_regs = rpm->status_regs + 0x400;
+       rpm->req_regs = rpm->status_regs + 0x600;
+       if (IS_ERR(rpm->status_regs))
+               return PTR_ERR(rpm->status_regs);
+
+       res = platform_get_resource(pdev, IORESOURCE_MEM, 1);

Dito.


[...]



[ ..

+       ret = irq_set_irq_wake(irq_ack, 1);
+       if (ret)
+               dev_warn(&pdev->dev, "failed to mark ack irq as
wakeup\n");
+

..]

Shouln't these be set as part of the pm suspend call, if the device is
wakeup capable?



Is there any reason to toggle this?

I'm not sure when this interrupt will actually be fired, but I don't see any
harm in keeping it wakup enabled at all times.

Typically the wake-up source is driven/enabled by the user. When the system goes to low-power state it would enable the wakeup on the irq. And when there is an interrupt it would wake up the system as part of resuming from low-power state.

Again if you what this interrupt to wakeup the system, I would expect pm_wakeup_event/related calls in the interrupt handler too.


[...]

+++ b/include/linux/mfd/qcom_rpm.h
@@ -0,0 +1,12 @@
+#ifndef __QCOM_RPM_H__
+#define __QCOM_RPM_H__
+
+#include <linux/types.h>
+
+struct device;
+struct qcom_rpm;
+
+struct qcom_rpm *dev_get_qcom_rpm(struct device *dev);
+int qcom_rpm_write(struct qcom_rpm *rpm, int resource, u32 *buf, size_t
count);


IMHO, dummy functions for these are required, otherwise you would get a
compilation errors on client drivers.


I didn't expect us to compile the children into a kernel that doesn't have the
rpm, as I see them as one entity. An exception would be if we want to add
COMPILE_TEST to the children, but that would require an extra change anyways.

Thanks for the review!

NP,

Thanks,
srini

Regards,
Bjorn

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux