On Wed, May 13, 2020 at 04:00:23PM +0200, Lars Povlsen wrote:
> This add support for the RX_SAMPLE_DLY register. If enabled in the
> Designware IP, it allows tuning of the rx data signal by means of an
> internal rx sample fifo.
>
> The register is located at offset 0xf0, and if the option is not
> enabled in the IP, changing the register will have no effect.
>
> Reviewed-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx>
> Signed-off-by: Lars Povlsen <lars.povlsen@xxxxxxxxxxxxx>
> ---
> drivers/spi/spi-dw.c | 7 +++++++
> drivers/spi/spi-dw.h | 2 ++
> 2 files changed, 9 insertions(+)
>
> diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
> index e572eb34a3c1a..32997f28fa5bb 100644
> --- a/drivers/spi/spi-dw.c
> +++ b/drivers/spi/spi-dw.c
> @@ -81,6 +81,9 @@ static ssize_t dw_spi_show_regs(struct file *file, char __user *user_buf,
> "DMATDLR: \t0x%08x\n", dw_readl(dws, DW_SPI_DMATDLR));
> len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
> "DMARDLR: \t0x%08x\n", dw_readl(dws, DW_SPI_DMARDLR));
> + len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
> + "RX_SAMPLE_DLY: \t0x%08x\n",
> + dw_readl(dws, DW_SPI_RX_SAMPLE_DLY));
debugfs_reg32 interface is now utilized in the driver to dump the registers
state. So this will have to be converted to just a new entry in the
dw_spi_dbgfs_regs array.
> len += scnprintf(buf + len, SPI_REGS_BUFSIZE - len,
> "=================================\n");
>
> @@ -315,6 +318,10 @@ static int dw_spi_transfer_one(struct spi_controller *master,
> spi_set_clk(dws, chip->clk_div);
> }
>
> + /* Apply RX sample delay, iff requested (nonzero) */
s/iff/if
> + if (dws->rx_sample_dly)
> + dw_writel(dws, DW_SPI_RX_SAMPLE_DLY, dws->rx_sample_dly);
> +
> dws->n_bytes = DIV_ROUND_UP(transfer->bits_per_word, BITS_PER_BYTE);
> dws->dma_width = DIV_ROUND_UP(transfer->bits_per_word, BITS_PER_BYTE);
>
> diff --git a/drivers/spi/spi-dw.h b/drivers/spi/spi-dw.h
> index 1bf5713e047d3..ed6e47b3f50da 100644
> --- a/drivers/spi/spi-dw.h
> +++ b/drivers/spi/spi-dw.h
> @@ -31,6 +31,7 @@
> #define DW_SPI_IDR 0x58
> #define DW_SPI_VERSION 0x5c
> #define DW_SPI_DR 0x60
> +#define DW_SPI_RX_SAMPLE_DLY 0xf0
> #define DW_SPI_CS_OVERRIDE 0xf4
>
> /* Bit fields in CTRLR0 */
> @@ -111,6 +112,7 @@ struct dw_spi {
>
> int cs_override;
> u32 reg_io_width; /* DR I/O width in bytes */
> + u8 rx_sample_dly; /* RX fifo tuning (option) */
This doesn't seem like a good place for this parameter. The sample delay is
SPI-slave specific. So as I see it, the parameter should be moved to the
chip_data.
-Sergey
> u16 bus_num;
> u16 num_cs; /* supported slave numbers */
> void (*set_cs)(struct spi_device *spi, bool enable);
> --
> 2.26.2
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
