Re: [PATCH v2 3/4] dt-bindings: display: ti,tfp410.txt: convert to yaml

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Ricardo,

Thank you for the patch.

On Thu, May 14, 2020 at 04:36:11PM +0200, Ricardo Cañuelo wrote:
> Convert the DT binding documentation for the TI TFP410 DPI-to-DVI
> encoder to json-schema.
> 
> The 'ti,deskew' is now an unsigned value from 0 to 7 instead of a signed
> value from -4 to 3. The rest of the binding is a direct translation from
> the old one.

I would have modified this in a separate patch.

> Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@xxxxxxxxxxxxx>
> ---
>  .../bindings/display/bridge/ti,tfp410.txt     |  66 ----------
>  .../bindings/display/bridge/ti,tfp410.yaml    | 124 ++++++++++++++++++
>  2 files changed, 124 insertions(+), 66 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,tfp410.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt
> deleted file mode 100644
> index 5ff4f64ef8e8..000000000000
> --- a/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt
> +++ /dev/null
> @@ -1,66 +0,0 @@
> -TFP410 DPI to DVI encoder
> -=========================
> -
> -Required properties:
> -- compatible: "ti,tfp410"
> -
> -Optional properties:
> -- powerdown-gpios: power-down gpio
> -- reg: I2C address. If and only if present the device node should be placed
> -  into the I2C controller node where the TFP410 I2C is connected to.
> -- ti,deskew: data de-skew in 350ps increments, from -4 to +3, as configured
> -  through th DK[3:1] pins. This property shall be present only if the TFP410
> -  is not connected through I2C.
> -
> -Required nodes:
> -
> -This device has two video ports. Their connections are modeled using the OF
> -graph bindings specified in [1]. Each port node shall have a single endpoint.
> -
> -- Port 0 is the DPI input port. Its endpoint subnode shall contain a
> -  pclk-sample and bus-width property and a remote-endpoint property as specified
> -  in [1].
> -  - If pclk-sample is not defined, pclk-sample = 0 should be assumed for
> -    backward compatibility.
> -  - If bus-width is not defined then bus-width = 24 should be assumed for
> -    backward compatibility.
> -    bus-width = 24: 24 data lines are connected and single-edge mode
> -    bus-width = 12: 12 data lines are connected and dual-edge mode
> -
> -- Port 1 is the DVI output port. Its endpoint subnode shall contain a
> -  remote-endpoint property is specified in [1].
> -
> -[1] Documentation/devicetree/bindings/media/video-interfaces.txt
> -
> -
> -Example
> --------
> -
> -tfp410: encoder@0 {
> -	compatible = "ti,tfp410";
> -	powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
> -	ti,deskew = <4>;
> -
> -	ports {
> -		#address-cells = <1>;
> -		#size-cells = <0>;
> -
> -		port@0 {
> -			reg = <0>;
> -
> -			tfp410_in: endpoint@0 {
> -				pclk-sample = <1>;
> -				bus-width = <24>;
> -				remote-endpoint = <&dpi_out>;
> -			};
> -		};
> -
> -		port@1 {
> -			reg = <1>;
> -
> -			tfp410_out: endpoint@0 {
> -				remote-endpoint = <&dvi_connector_in>;
> -			};
> -		};
> -	};
> -};
> diff --git a/Documentation/devicetree/bindings/display/bridge/ti,tfp410.yaml b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.yaml
> new file mode 100644
> index 000000000000..a9f4fd8ea621
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.yaml
> @@ -0,0 +1,124 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/ti,tfp410.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: TFP410 DPI to DVI encoder
> +
> +maintainers:
> +  - Tomi Valkeinen <tomi.valkeinen@xxxxxx>
> +  - Jyri Sarha <jsarha@xxxxxx>
> +
> +properties:
> +  compatible:
> +    const: ti,tfp410
> +
> +  reg:
> +    description: I2C address of the device.
> +    maxItems: 1
> +
> +  powerdown-gpios:
> +    maxItems: 1
> +
> +  ti,deskew:
> +    description:
> +      Data de-skew value in 350ps increments, from 0 to 7, as configured
> +      through the DK[3:1] pins. The de-skew multiplier is computed as
> +      (DK[3:1] - 4), so it ranges from -4 to 3. This property shall be
> +      present only if the TFP410 is not connected through I2C.

I'd replace the last sentence with

if:
  required:
    - reg
then:
  properties:
    ti,deskew: false
else:
  required:
    - ti,deskew

(between the required: and additionalProperties: objects below)

> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    minimum: 0
> +    maximum: 7
> +
> +  ports:
> +    description:
> +      A node containing input and output port nodes with endpoint
> +      definitions as documented in
> +      Documentation/devicetree/bindings/media/video-interfaces.txt
> +    type: object
> +
> +    properties:
> +      port@0:
> +        description: DPI input port.
> +        type: object
> +
> +        properties:
> +          reg:
> +            const: 0
> +
> +          endpoint:
> +            type: object
> +
> +            properties:
> +              pclk-sample:
> +                description:
> +                  Endpoint sampling edge. If not defined, pclk-sample =
> +                  0 should be assumed for backwards compatibility.

Should the second sentence be dropped, as it's expressed with default: 0
?

> +                enum:
> +                  - 0  # Falling edge
> +                  - 1  # Rising edge
> +                default: 0
> +
> +              bus-width:
> +                description:
> +                  Endpoint bus width. If not defined, bus-width = 24
> +                  should be assumed for backwards compatibility.

Same here for the second sentence.

With these small issues fixed,

Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>

> +                enum:
> +                  - 12  # 12 data lines connected and dual-edge mode
> +                  - 24  # 24 data lines connected and single-edge mode
> +                default: 24
> +
> +      port@1:
> +        description: DVI output port.
> +        type: object
> +
> +        properties:
> +          reg:
> +            const: 1
> +
> +          endpoint:
> +            type: object
> +
> +    required:
> +      - port@0
> +      - port@1
> +
> +required:
> +  - compatible
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +
> +    tfp410: encoder {
> +        compatible = "ti,tfp410";
> +        powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
> +        ti,deskew = <3>;
> +
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port@0 {
> +                reg = <0>;
> +                tfp410_in: endpoint {
> +                    pclk-sample = <1>;
> +                    bus-width = <24>;
> +                    remote-endpoint = <&dpi_out>;
> +                };
> +            };
> +
> +            port@1 {
> +                reg = <1>;
> +                tfp410_out: endpoint {
> +                    remote-endpoint = <&dvi_connector_in>;
> +                };
> +            };
> +        };
> +    };
> +
> +...

-- 
Regards,

Laurent Pinchart



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux