On Sun, May 24, 2020 at 12:41:14PM +0100, Jonathan Cameron wrote: > On Wed, 20 May 2020 21:46:40 +0200 > Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx> wrote: > > > Converts documentation from txt format to yaml. > > > > Signed-off-by: Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx> > > A reminder on the maintainer bit as that thread crossed with > this one. Also, drop the spi-max-frequency as we don't need > to mention it explicitly for this device. > > Thanks, > > Jonathan > Thank you, I'll remove it today. > > > --- > > .../devicetree/bindings/iio/imu/bmi160.txt | 37 --------- > > .../bindings/iio/imu/bosch,bmi160.yaml | 76 +++++++++++++++++++ > > 2 files changed, 76 insertions(+), 37 deletions(-) > > delete mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.txt > > create mode 100644 Documentation/devicetree/bindings/iio/imu/bosch,bmi160.yaml > > > > diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.txt b/Documentation/devicetree/bindings/iio/imu/bmi160.txt > > deleted file mode 100644 > > index 900c169de00f..000000000000 > > --- a/Documentation/devicetree/bindings/iio/imu/bmi160.txt > > +++ /dev/null > > @@ -1,37 +0,0 @@ > > -Bosch BMI160 - Inertial Measurement Unit with Accelerometer, Gyroscope > > -and externally connectable Magnetometer > > - > > -https://www.bosch-sensortec.com/bst/products/all_products/bmi160 > > - > > -Required properties: > > - - compatible : should be "bosch,bmi160" > > - - reg : the I2C address or SPI chip select number of the sensor > > - - spi-max-frequency : set maximum clock frequency (only for SPI) > > - > > -Optional properties: > > - - interrupts : interrupt mapping for IRQ > > - - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt > > - input, set to "INT2" if INT2 pin should be used instead > > - - drive-open-drain : set if the specified interrupt pin should be configured as > > - open drain. If not set, defaults to push-pull. > > - > > -Examples: > > - > > -bmi160@68 { > > - compatible = "bosch,bmi160"; > > - reg = <0x68>; > > - > > - interrupt-parent = <&gpio4>; > > - interrupts = <12 IRQ_TYPE_EDGE_RISING>; > > - interrupt-names = "INT1"; > > -}; > > - > > -bmi160@0 { > > - compatible = "bosch,bmi160"; > > - reg = <0>; > > - spi-max-frequency = <10000000>; > > - > > - interrupt-parent = <&gpio2>; > > - interrupts = <12 IRQ_TYPE_LEVEL_LOW>; > > - interrupt-names = "INT2"; > > -}; > > diff --git a/Documentation/devicetree/bindings/iio/imu/bosch,bmi160.yaml b/Documentation/devicetree/bindings/iio/imu/bosch,bmi160.yaml > > new file mode 100644 > > index 000000000000..46cb4fde1165 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/iio/imu/bosch,bmi160.yaml > > @@ -0,0 +1,76 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/iio/imu/bosch,bmi160.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Bosch BMI160 > > + > > +maintainers: > > + - Daniel Baluta <daniel.baluta@xxxxxxx> (?) > > Daniel's reply crossed with this. Given he's moved on to other things > he's not happy to be listed as maintainer here. > > Given other threads, either put yourself here if you are happy to maintain > the binding, or fall back to me but use my kernel.org address. > > Jonathan Cameron <jic23@xxxxxxxxxx> > > I don't mind either way. > Thank you, I'll add you then for this binding. Thank for your help, Best regards, Jonathan Albrieux > > > + > > +description: | > > + Inertial Measurement Unit with Accelerometer, Gyroscope and externally > > + connectable Magnetometer > > + https://www.bosch-sensortec.com/bst/products/all_products/bmi160 > > + > > +properties: > > + compatible: > > + const: bosch,bmi160 > > + > > + reg: > > + maxItems: 1 > > + > > + spi-max-frequency: > > + maxItems: 1 > > spi-max-frequency doesn't need to be here at all. We aren't trying to list > all of the properties that might be present - but rather those that > are either required or that are part of the description of the device. > This one is a generic spi binding that may or may not be present. > > > + > > + interrupts: > > + maxItems: 1 > > + > > + interrupt-names: > > + enum: > > + - INT1 > > + - INT2 > > + description: | > > + set to "INT1" if INT1 pin should be used as interrupt input, set > > + to "INT2" if INT2 pin should be used instead > > + > > + drive-open-drain: > > + description: | > > + set if the specified interrupt pin should be configured as > > + open drain. If not set, defaults to push-pull. > > + > > +required: > > + - compatible > > + - reg > > + > > +examples: > > + - | > > + // Example for I2C > > + i2c { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + bmi160@68 { > > + compatible = "bosch,bmi160"; > > + reg = <0x68>; > > + interrupt-parent = <&gpio4>; > > + interrupts = <12 1>; > > + interrupt-names = "INT1"; > > + }; > > + }; > > + - | > > + // Example for SPI > > + spi { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + bmi160@0 { > > + compatible = "bosch,bmi160"; > > + reg = <0>; > > + spi-max-frequency = <10000000>; > > + interrupt-parent = <&gpio2>; > > + interrupts = <12 1>; > > + interrupt-names = "INT2"; > > + }; > > + }; >
