Hi Rob, On Mon, May 11, 2020 at 11:02:07AM -0500, Rob Herring wrote: > On Sat, May 09, 2020 at 04:06:26PM +0800, Dongchun Zhu wrote: > > Add DT bindings documentation for Omnivision OV02A10 image sensor. > > > > Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > --- > > .../bindings/media/i2c/ovti,ov02a10.yaml | 184 +++++++++++++++++++++ > > MAINTAINERS | 7 + > > 2 files changed, 191 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > new file mode 100644 > > index 0000000..5468d1b > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > @@ -0,0 +1,184 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +# Copyright (c) 2020 MediaTek Inc. > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings > > + > > +maintainers: > > + - Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > + > > +description: |- > > + The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel > > + image sensor, which is the latest production derived from Omnivision's CMOS > > + image sensor technology. Ihis chip supports high frame rate speeds up to 30fps > > + @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The > > + sensor output is available via CSI-2 serial data output. > > + > > +properties: > > + compatible: > > + const: ovti,ov02a10 > > + > > + reg: > > + description: I2C device address > > Drop this. Nothing specific to this device. > > > + maxItems: 1 > > + > > + clocks: > > + items: > > + - description: top mux camtg clock > > + - description: devider clock > > typo > > > + > > + clock-names: > > + items: > > + - const: eclk > > + - const: freq_mux > > + > > + clock-frequency: > > + description: > > + Frequency of the eclk clock in Hertz. > > + > > + dovdd-supply: > > + description: > > + Definition of the regulator used as interface power supply. > > + > > + avdd-supply: > > + description: > > + Definition of the regulator used as analog power supply. > > + > > + dvdd-supply: > > + description: > > + Definition of the regulator used as digital power supply. > > + > > + powerdown-gpios: > > + maxItems: 1 > > + > > + reset-gpios: > > + maxItems: 1 I asked a question about defining GPIO polarities some time ago, but I guess it slipped through. The chip documentation calls the reset pin as "RST_PAD (low level reset)". Where should the inversion be handled, in the driver or here, by having the DT include a necessary flag in the specifier? Best regards, Tomasz
