On Tue, May 19, 2020 at 09:50:57AM +0200, Jonathan Albrieux wrote: > Converts documentation from txt format to yaml > > Signed-off-by: Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx> > --- > .../devicetree/bindings/iio/imu/bmi160.txt | 37 -------- > .../devicetree/bindings/iio/imu/bmi160.yaml | 84 +++++++++++++++++++ > 2 files changed, 84 insertions(+), 37 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.txt > create mode 100644 Documentation/devicetree/bindings/iio/imu/bmi160.yaml Use compatible string for filename: bosch,bmi160.yaml > > diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.txt b/Documentation/devicetree/bindings/iio/imu/bmi160.txt > deleted file mode 100644 > index 900c169de00f..000000000000 > --- a/Documentation/devicetree/bindings/iio/imu/bmi160.txt > +++ /dev/null > @@ -1,37 +0,0 @@ > -Bosch BMI160 - Inertial Measurement Unit with Accelerometer, Gyroscope > -and externally connectable Magnetometer > - > -https://www.bosch-sensortec.com/bst/products/all_products/bmi160 > - > -Required properties: > - - compatible : should be "bosch,bmi160" > - - reg : the I2C address or SPI chip select number of the sensor > - - spi-max-frequency : set maximum clock frequency (only for SPI) > - > -Optional properties: > - - interrupts : interrupt mapping for IRQ > - - interrupt-names : set to "INT1" if INT1 pin should be used as interrupt > - input, set to "INT2" if INT2 pin should be used instead > - - drive-open-drain : set if the specified interrupt pin should be configured as > - open drain. If not set, defaults to push-pull. > - > -Examples: > - > -bmi160@68 { > - compatible = "bosch,bmi160"; > - reg = <0x68>; > - > - interrupt-parent = <&gpio4>; > - interrupts = <12 IRQ_TYPE_EDGE_RISING>; > - interrupt-names = "INT1"; > -}; > - > -bmi160@0 { > - compatible = "bosch,bmi160"; > - reg = <0>; > - spi-max-frequency = <10000000>; > - > - interrupt-parent = <&gpio2>; > - interrupts = <12 IRQ_TYPE_LEVEL_LOW>; > - interrupt-names = "INT2"; > -}; > diff --git a/Documentation/devicetree/bindings/iio/imu/bmi160.yaml b/Documentation/devicetree/bindings/iio/imu/bmi160.yaml > new file mode 100644 > index 000000000000..6b464ce5ed0b > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/imu/bmi160.yaml > @@ -0,0 +1,84 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/imu/bmi160.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Bosch BMI160 > + > +maintainers: > + - can't find a mantainer, author is Daniel Baluta <daniel.baluta@xxxxxxxxx> Would help to Cc him perhaps. > + > +description: | > + Inertial Measurement Unit with Accelerometer, Gyroscope and externally > + connectable Magnetometer > + https://www.bosch-sensortec.com/bst/products/all_products/bmi160 > + > +properties: > + compatible: > + const: bosch,bmi160 > + > + reg: > + maxItems: 1 > + description: the I2C address or SPI chip select number of the sensor > + > + spi-max-frequency: > + maxItems: 1 > + description: set maximum clock frequency (required only for SPI) > + > + interrupts: > + maxItems: 1 > + description: interrupt mapping for IRQ No need for description if not adding anything unique for this device. > + > + interrupt-names: > + minItems: 1 > + maxItems: 1 > + items: > + enum: > + - INT1 > + - INT2 Just the enum is enough. > + description: | > + set to "INT1" if INT1 pin should be used as interrupt input, set > + to "INT2" if INT2 pin should be used instead > + > + drive-open-drain: > + description: | > + set if the specified interrupt pin should be configured as > + open drain. If not set, defaults to push-pull. > + > +required: > + - compatible > + - reg > + > +examples: > + - | > + // Example for I2C > + i2c@78b7000 { > + reg = <0x78b6000 0x600>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + bmi160@68 { > + compatible = "bosch,bmi160"; > + reg = <0x68>; > + interrupt-parent = <&gpio4>; > + interrupts = <12 1>; > + interrupt-names = "INT1"; > + }; > + - | > + // Example for SPI > + spi@78b7000 { > + reg = <0x78b7000 0x600>, > + <0x7884000 0x23000>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + bmi160@0 { > + compatible = "bosch,bmi160"; > + reg = <0>; > + spi-max-frequency = <10000000>; > + interrupt-parent = <&gpio2>; > + interrupts = <12 1>; > + interrupt-names = "INT2"; > + }; > + }; > -- > 2.17.1 >
