Re: [PATCH v4 5/5] arm64: dts: Add node for ufs exynos7

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sat, 2020-04-04 at 21:33 +0200, Paweł Chmiel wrote:
> On Sat, 2020-04-04 at 23:45 +0530, Alim Akhtar wrote:
> Hi Alim,
> > Hi Pawel,
> > 
> > > -----Original Message-----
> > > From: Paweł Chmiel <pawel.mikolaj.chmiel@xxxxxxxxx>
> > > Sent: 03 April 2020 22:22
> > > To: Alim Akhtar <alim.akhtar@xxxxxxxxxxx>; robh+dt@xxxxxxxxxx;
> > > devicetree@xxxxxxxxxxxxxxx; linux-scsi@xxxxxxxxxxxxxxx
> > > Cc: krzk@xxxxxxxxxx; avri.altman@xxxxxxx; martin.petersen@xxxxxxxxxx;
> > > kwmad.kim@xxxxxxxxxxx; stanley.chu@xxxxxxxxxxxx;
> > > cang@xxxxxxxxxxxxxx; linux-samsung-soc@xxxxxxxxxxxxxxx; linux-arm-
> > > kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
> > > Subject: Re: [PATCH v4 5/5] arm64: dts: Add node for ufs exynos7
> > > 
> > > Hi Alim
> > > 
> > > Looking at vendor sources, my device is using the same gpios for
> > > urfs_rst_n and ufs_refclk_out like Espresso (with one difference -
> > > ufs_rst_n shouldn't be pulled up).
> > > 
> > > About regulators (it would be easier if dts would have all regulators).
> > > It's also using s2mps15 as Espresso, but it vendor dts had only 8 (of
> > > 10 possible bucks, one missing was for UFS) and 14 ldos (of 27
> > > possible), where almost all rails are connected to something.
> > > 
> > > I'm wondering how it's working on Espresso, because when adding correct
> > > regulators for ufs (vccq = buck10 from s2mps15, always enabled for
> > > testing plus vccq2 and vccq = two regulators enabled by one gpio,
> > > enabled at boot by firmware), ufs wasn't still working because it was
> > > then failing at defer probe (s2mps15 was probed after ufs)
> > > 
> > > [    0.962482] exynos-ufshc 15570000.ufs: ufshcd_get_vreg: vccq get
> > > failed, err=-517
> > > 
> > As I said, this is very specific to the board, on Espresso we have LDO12 connected to UFS_RESETn.
> > Either make all of them as always-on, or just disabled s2mps15 
> > (default voltage supply should be ok, unless bootloader on your board does have messed too much with PMIC)
> >  
> > > After that boot would just stop/hang.
> > > 
> > > After making a "dirty fix" by making s2mps15 regulator driver use
> > > subsys_initcall (like in vendor sources) and ufs late_initcall (to give
> > > it more time to setup and get it working and solve it later),
> > > i had to mark following clocks as CLK_IGNORE_UNUSED to be able to bring
> > > link up (it replicates setting done by vendor kernel, which enables
> > > them on boot):
> > > - "phyclk_ufs20_rx1_symbol_user"
> > > - "phyclk_ufs20_rx0_symbol_user"
> > > - "phyclk_ufs20_tx0_symbol_user"
> > > 
> > Coming to these clocks, all these are supplied by default, my best guess is since you are using an actual product (S6 edge), they might have optimized for power saving 
> > And most likely all clock might be  gated initially. In my case all are set to default.
> > I have attached a small change in the exynos7 dts and phy driver clock handling, please try this attached patch and let me know if this helps in removing some of your hacks.
> > In the later SoCs these clocks are not in this form, so I didn't included in my current patch set, If this works for your, will add as an optional for exynos7/7420.
> > I also assume you are using clk-exynos7.c and my posted ufs driver.
> Yes, i'm using clk-exynos7 (and other exynos7 drivers/dts/etc).
> It would be great if someone could say how exynos7 and exynos7420 are
> similar. For now it looks like that only difference is that exynos7 has
> only 4 cores (a57) where 7420 has 4xa53 + 4xa57.
> It would be very valuable information for me so i could know how much i
> could reuse my device.
> > > Now it's able to bring both device and link, but it fails at
> > > ufshcd_uic_change_pwr_mode.
> > > 
> > Can you please use the exact ufs and ufs-phy device node as in my patch?
> With Your patch + removed my changes to clocks (removed fix for wrong
> clock order in dts + removed CLK_IGNORE_UNUSED from symbol clocks in
> clk-exynos7) it's finally able to detect my UFS device!! 
> 
> (but of fails later...with constant error spam in kernel log).
> 
> [    1.383481] exynos-ufshc 15570000.ufs: ufshcd_populate_vreg: Unable
> to find vdd-hba-supply regulator, assuming enabled
> [    1.390060] exynos-ufshc 15570000.ufs: ufshcd_populate_vreg: unable
> to find vcc-max-microamp
> [    1.398465] exynos-ufshc 15570000.ufs: ufshcd_populate_vreg: unable
> to find vccq-max-microamp
> [    1.406968] exynos-ufshc 15570000.ufs: ufshcd_populate_vreg: unable
> to find vccq2-max-microamp
> [    1.415569] exynos-ufshc 15570000.ufs: ufshcd_init_clocks: clk:
> core_clk, rate: 100000000
> [    1.423715] exynos-ufshc 15570000.ufs: ufshcd_init_clocks: clk:
> sclk_unipro_main, rate: 167000000
> [    1.432569] exynos-ufshc 15570000.ufs: __ufshcd_setup_clocks: clk:
> core_clk enabled
> [    1.440205] exynos-ufshc 15570000.ufs: __ufshcd_setup_clocks: clk:
> sclk_unipro_main enabled
> [    1.449613] scsi host0: ufshcd
> [    1.452179] samsung-ufs-phy 15571800.ufs-phy: MPHY ref_clk_rate =
> 26000000
> [    1.458448] samsung-ufs-phy 15571800.ufs-phy: MPHY
> ref_parent_clk_rate = 26000000
> [    1.487288] exynos-ufshc 15570000.ufs: ufshcd_print_pwr_info:[RX,
> TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate =
> 0
> [    2.025569] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd041 val
> 0x1fff error code 1
> [    2.025715] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd041 val
> 0x1fff failed 0 retries
> [    2.025880] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd042 val
> 0xffff error code 1
> [    2.027354] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd042 val
> 0xffff failed 0 retries
> [    2.035583] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd043 val
> 0x7fff error code 1
> [    2.043465] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd043 val
> 0x7fff failed 0 retries
> [    2.054049] exynos-ufshc 15570000.ufs: Power mode change 0 : Fast
> series_B G_2 L_2
> [    2.059261] exynos-ufshc 15570000.ufs: ufshcd_print_pwr_info:[RX,
> TX]: gear=[2, 2], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
> [    2.071307] exynos-ufshc 15570000.ufs: ufshcd_init_icc_levels:
> setting icc_level 0x0
> [    2.081624] exynos-ufshc 15570000.ufs: ufshcd_set_queue_depth:
> activate tcq with queue depth 1
> [    2.087576] scsi 0:0:0:49488: scsi_add_lun: correcting incorrect
> peripheral device type 0x0 for W-LUN 0x            c150hN
> [    2.098400] scsi 0:0:0:49488: Well-known LUN    SAMSUNG  KLUBG4G1BD-
> E0B1  0200 PQ: 0 ANSI: 6
> [    2.107585] exynos-ufshc 15570000.ufs: ufshcd_set_queue_depth:
> activate tcq with queue depth 16
> [    2.115588] scsi 0:0:0:49476: scsi_add_lun: correcting incorrect
> peripheral device type 0x0 for W-LUN 0x            c144hN
> [    2.126519] scsi 0:0:0:49476: Well-known LUN    SAMSUNG  KLUBG4G1BD-
> E0B1  0200 PQ: 0 ANSI: 6
> [    2.135534] exynos-ufshc 15570000.ufs: ufshcd_set_queue_depth:
> activate tcq with queue depth 1
> [    2.143612] scsi 0:0:0:49456: scsi_add_lun: correcting incorrect
> peripheral device type 0x0 for W-LUN 0x            c130hN
> [    2.154543] scsi 0:0:0:49456: Well-known LUN    SAMSUNG  KLUBG4G1BD-
> E0B1  0200 PQ: 0 ANSI: 6
> [    2.163597] exynos-ufshc 15570000.ufs: ufshcd_set_queue_depth:
> activate tcq with queue depth 16
> [    2.171721] scsi 0:0:0:0: Direct-Access     SAMSUNG  KLUBG4G1BD-
> E0B1  0200 PQ: 0 ANSI: 6
> [    2.180352] exynos-ufshc 15570000.ufs: OCS error from controller = 7
> for tag 0
> [    2.186921] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
> [    2.193230] host_regs: 00000010: 00000101 00007fce 00000c96 00000000
> [    2.199565] host_regs: 00000020: 00000000 00030e75 00000000 00000000
> [    2.205899] host_regs: 00000030: 0000010f 00000000 80000010 00000000
> [    2.212234] host_regs: 00000040: 00000000 00000000 00000000 00000000
> [    2.218568] host_regs: 00000050: f8d64000 00000000 00000000 00000000
> [    2.224903] host_regs: 00000060: 00000001 00000000 00000000 00000000
> [    2.231237] host_regs: 00000070: f8da2000 00000000 00000000 00000000
> [    2.237572] host_regs: 00000080: 00000001 00000000 00000000 00000000
> [    2.243907] host_regs: 00000090: 00000002 95190000 00000000 00000000
> [    2.250242] exynos-ufshc 15570000.ufs: hba->ufs_version = 0x200,
> hba->capabilities = 0x383ff0f
> 
> Full bootlog 
> https://gist.github.com/PabloPL/0bcb24492f4ab6e9703c2a4ea20ceb18
> kernel source: https://github.com/PabloPL/linux/tree/ufs-mainline
> dts file: exynos7-zeroflt.dts (it should be zerolt, but will be
> fixed/changed later).

Actually, after waiting enough time (about 15 or even more sec of that
error "spam"), was able to mount partitions and manipulate files there.

So for me the only issue to solve are defered probe when regulators are
not yet found (for example when pmic is probed after ufs) and not sure
what about that errors (despite working ufs).

Thanks for all
> 
> Thanks
> > > [    1.411547] exynos-ufshc 15570000.ufs: ufshcd_init_clocks: clk:
> > > core_clk, rate: 100000000
> > > [    1.419698] exynos-ufshc 15570000.ufs: ufshcd_init_clocks: clk:
> > > sclk_unipro_main, rate: 167000000
> > > [    1.428550] exynos-ufshc 15570000.ufs: __ufshcd_setup_clocks: clk:
> > > core_clk enabled
> > > [    1.436200] exynos-ufshc 15570000.ufs: __ufshcd_setup_clocks: clk:
> > > sclk_unipro_main enabled
> > > [    1.445704] scsi host0: ufshcd
> > > [    1.465684] exynos-ufshc 15570000.ufs: ufshcd_print_pwr_info:[RX,
> > > TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate
> > > =
> > > 0
> > > [    2.023699] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd041 val
> > > 0x1fff error code 1
> > > [    2.023846] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd041 val
> > > 0x1fff failed 0 retries
> > > [    2.024025] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd042 val
> > > 0xffff error code 1
> > > [    2.025457] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd042 val
> > > 0xffff failed 0 retries
> > > [    2.033777] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd043 val
> > > 0x7fff error code 1
> > > [    2.041607] exynos-ufshc 15570000.ufs: dme-set: attr-id 0xd043 val
> > > 0x7fff failed 0 retries
> > > [    2.067809] exynos-ufshc 15570000.ufs: pwr ctrl cmd 0x2 failed, host
> > > upmcrs:0x5
> > > [    2.067953] exynos-ufshc 15570000.ufs: UFS Host state=0
> > > [    2.068056] exynos-ufshc 15570000.ufs: outstanding reqs=0x0
> > > tasks=0x0
> > > [    2.068759] exynos-ufshc 15570000.ufs: saved_err=0x0,
> > > saved_uic_err=0x0
> > > [    2.075368] exynos-ufshc 15570000.ufs: Device power mode=1, UIC link
> > > state=1
> > > [    2.082392] exynos-ufshc 15570000.ufs: PM in progress=0, sys.
> > > suspended=0
> > > [    2.089158] exynos-ufshc 15570000.ufs: Auto BKOPS=0, Host self-
> > > block=0
> > > [    2.095667] exynos-ufshc 15570000.ufs: Clk gate=1
> > > [    2.100354] exynos-ufshc 15570000.ufs: error handling flags=0x0,
> > > req. abort count=0
> > > [    2.107987] exynos-ufshc 15570000.ufs: Host capabilities=0x383ff0f,
> > > caps=0x0
> > > [    2.115018] exynos-ufshc 15570000.ufs: quirks=0x780, dev.
> > > quirks=0xc4
> > > [    2.121443] exynos-ufshc 15570000.ufs: ufshcd_print_pwr_info:[RX,
> > > TX]: gear=[1, 1], lane[1, 1], pwr[SLOWAUTO_MODE, SLOWAUTO_MODE], rate
> > > =
> > > 0
> > > [    2.133960] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
> > > [    2.140268] host_regs: 00000010: 00000101 00007fce 00000000 00000000
> > > [    2.146604] host_regs: 00000020: 00000000 00030a75 00000000 00000000
> > > [    2.152940] host_regs: 00000030: 0000050f 00000000 80000010 00000000
> > > [    2.159271] host_regs: 00000040: 00000000 00000000 00000000 00000000
> > > [    2.165609] host_regs: 00000050: f9587000 00000000 00000000 00000000
> > > [    2.171944] host_regs: 00000060: 00000001 00000000 00000000 00000000
> > > [    2.178278] host_regs: 00000070: f958a000 00000000 00000000 00000000
> > > [    2.184609] host_regs: 00000080: 00000001 00000000 00000000 00000000
> > > [    2.190945] host_regs: 00000090: 00000002 15710000 00000000 00000000
> > > [    2.197282] exynos-ufshc 15570000.ufs: hba->ufs_version = 0x200,
> > > hba->capabilities = 0x383ff0f
> > > [    2.205869] exynos-ufshc 15570000.ufs: hba->outstanding_reqs = 0x0,
> > > hba->outstanding_tasks = 0x0
> > > [    2.214636] exynos-ufshc 15570000.ufs: last_hibern8_exit_tstamp at 0
> > > us, hibern8_exit_cnt = 0
> > > [    2.223141] exynos-ufshc 15570000.ufs: No record of pa_err
> > > [    2.228606] exynos-ufshc 15570000.ufs: No record of dl_err
> > > [    2.234071] exynos-ufshc 15570000.ufs: No record of nl_err
> > > [    2.239540] exynos-ufshc 15570000.ufs: No record of tl_err
> > > [    2.245007] exynos-ufshc 15570000.ufs: No record of dme_err
> > > [    2.250558] exynos-ufshc 15570000.ufs: No record of auto_hibern8_err
> > > [    2.256895] exynos-ufshc 15570000.ufs: No record of fatal_err
> > > [    2.262624] exynos-ufshc 15570000.ufs: No record of
> > > link_startup_fail
> > > [    2.269044] exynos-ufshc 15570000.ufs: No record of resume_fail
> > > [    2.274942] exynos-ufshc 15570000.ufs: No record of suspend_fail
> > > [    2.280931] exynos-ufshc 15570000.ufs: No record of dev_reset
> > > [    2.286659] exynos-ufshc 15570000.ufs: No record of host_reset
> > > [    2.292475] exynos-ufshc 15570000.ufs: No record of task_abort
> > > [    2.298290] exynos-ufshc 15570000.ufs: ufshcd_change_power_mode:
> > > power mode change failed 5
> > > [    2.306619] exynos-ufshc 15570000.ufs: ufshcd_probe_hba: Failed
> > > setting power mode, err = 5
> > > [    2.315144] exynos-ufshc 15570000.ufs: __ufshcd_setup_clocks: clk:
> > > core_clk disabled
> > > 
> > > And here boot would just stop/hang.
> > > 
> > > Thanks for all hints.
> > > 
> > > > > > > Also looking at clk-exynos7 driver seems to confirm this.
> > > > > > > 
> > > > > > > > +		};
> > > > > > > > +
> > > > > > > >  		usbdrd_phy: phy@15500000 {
> > > > > > > >  			compatible = "samsung,exynos7-usbdrd-phy";
> > > > > > > >  			reg = <0x15500000 0x100>;




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux