Hi Laurent, On Fri, Mar 13, 2020 at 9:27 PM Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> wrote: > > Hi Prabhakar, > > On Fri, Mar 13, 2020 at 09:25:01PM +0000, Prabhakar Mahadev Lad wrote: > > On Sent: 13 March 2020 21:20, Laurent Pinchart wrote: > > > On Fri, Mar 13, 2020 at 09:12:31PM +0000, Lad Prabhakar wrote: > > > > Use assigned-clock-rates to specify the clock rate. Also mark > > > > clock-frequency property as deprecated. > > > > > > I would phrase it the other way around, this patch mainly deprecates clock- > > > frequency, and as a side effect recommends usage of assigned-clock-rates. > > > > > > "Deprecate usage of the clock-frequency propertly. The preferred method > > > to set clock rates is to use assigned-clock-rates." > > > > Agreed will do that. > > > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> > > > > --- > > > > Documentation/devicetree/bindings/media/i2c/ov5645.txt | 5 +++-- > > > > 1 file changed, 3 insertions(+), 2 deletions(-) > > > > > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt > > > > b/Documentation/devicetree/bindings/media/i2c/ov5645.txt > > > > index 72ad992..e62fe82 100644 > > > > --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt > > > > +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt > > > > @@ -8,7 +8,7 @@ Required Properties: > > > > - compatible: Value should be "ovti,ov5645". > > > > - clocks: Reference to the xclk clock. > > > > - clock-names: Should be "xclk". > > > > -- clock-frequency: Frequency of the xclk clock. > > > > +- clock-frequency (deprecated): Frequency of the xclk clock. > > > > > > I would drop this completely. Drivers need to ensure backward compatibility, > > > but DT bindings should only document the latest version, the history is > > > available in git. > > > > > Sure will drop it. > > > > > Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > > > > > > While at it, can I enlist you to convert these bindings to yaml ? :-) > > > > > Sure will do the honours , will make sure yaml patch is ontop of this patch too. > Shall I enlist you as the maintainer in the json-schema ? dt_binding_check says 'maintainers' is a required property. Cheers, --Prabhakar Lad > Thank you :-) > > > > > - enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds > > > > to the hardware pin PWDNB which is physically active low. > > > > - reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to > > > > @@ -37,7 +37,8 @@ Example: > > > > > > > > clocks = <&clks 200>; > > > > clock-names = "xclk"; > > > > -clock-frequency = <24000000>; > > > > +assigned-clocks = <&clks 200>; > > > > +assigned-clock-rates = <24000000>; > > > > > > > > vdddo-supply = <&camera_dovdd_1v8>; > > > > vdda-supply = <&camera_avdd_2v8>; > > -- > Regards, > > Laurent Pinchart > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
