The .txt binding explains:
"
The following optional properties only apply to
RGB and YUV input modes and
can be omitted for BT.656 input modes:
"
This constraint is not implmented in the DT Schema.
The original binding from the .txt file referenced
properties that is included in panel-timing.yaml.
These properties are kept here as we want as close to a 1:1
conversion as we can. If the properties should be dropped
from the binding then this is a follow-up patch.
The properties in question are:
- pixelclk-active
- de-active
- hsync-active
- vsync-active
Signed-off-by: Sam Ravnborg <sam@xxxxxxxxxxxx>
Cc: Linus Walleij <linus.walleij@xxxxxxxxxx>
Cc: Thierry Reding <thierry.reding@xxxxxxxxx>
Cc: Sam Ravnborg <sam@xxxxxxxxxxxx>
---
.../bindings/display/panel/ilitek,ili9322.txt | 49 ----------
.../display/panel/ilitek,ili9322.yaml | 90 +++++++++++++++++++
2 files changed, 90 insertions(+), 49 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9322.yaml
diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
deleted file mode 100644
index 3d5ce6ad6ec7..000000000000
--- a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
+++ /dev/null
@@ -1,49 +0,0 @@
-Ilitek ILI9322 TFT panel driver with SPI control bus
-
-This is a driver for 320x240 TFT panels, accepting a variety of input
-streams that get adapted and scaled to the panel. The panel output has
-960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and
-VCOMH outputs.
-
-Required properties:
- - compatible: "dlink,dir-685-panel", "ilitek,ili9322"
- (full system-specific compatible is always required to look up configuration)
- - reg: address of the panel on the SPI bus
-
-Optional properties:
- - vcc-supply: core voltage supply, see regulator/regulator.txt
- - iovcc-supply: voltage supply for the interface input/output signals,
- see regulator/regulator.txt
- - vci-supply: voltage supply for analog parts, see regulator/regulator.txt
- - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt
-
- The following optional properties only apply to RGB and YUV input modes and
- can be omitted for BT.656 input modes:
-
- - pixelclk-active: see display/panel/display-timing.txt
- - de-active: see display/panel/display-timing.txt
- - hsync-active: see display/panel/display-timing.txt
- - vsync-active: see display/panel/display-timing.txt
-
-The panel must obey the rules for a SPI slave device as specified in
-spi/spi-bus.txt
-
-The device node can contain one 'port' child node with one child
-'endpoint' node, according to the bindings defined in
-media/video-interfaces.txt. This node should describe panel's video bus.
-
-Example:
-
-panel: display@0 {
- compatible = "dlink,dir-685-panel", "ilitek,ili9322";
- reg = <0>;
- vcc-supply = <&vdisp>;
- iovcc-supply = <&vdisp>;
- vci-supply = <&vdisp>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&display_out>;
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.yaml b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.yaml
new file mode 100644
index 000000000000..9f165f12fc32
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.yaml
@@ -0,0 +1,90 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/ilitek,ili9322.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ilitek ILI9322 TFT panel driver with SPI control bus
+
+maintainers:
+ - Linus Walleij <linus.walleij@xxxxxxxxxx>
+
+description: |
+ This is a driver for 320x240 TFT panels, accepting a variety of input
+ streams that get adapted and scaled to the panel. The panel output has
+ 960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and
+ VCOMH outputs.
+
+ The panel must obey the rules for a SPI slave device as specified in
+ spi/spi-bus.txt
+
+allOf:
+ - $ref: panel-common.yaml#
+ - $ref: ../../spi/spi-slave.yaml#
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - dlink,dir-685-panel
+
+ - const: ilitek,ili9322
+
+ reset-gpios: true
+ port: true
+
+ vcc-supply:
+ description: Core voltage supply
+
+ iovcc-supply:
+ description: Voltage supply for the interface input/output signals
+
+ vci-supply:
+ description: Voltage supply for analog parts
+
+ pixelclk-active:
+ description: |
+ Optional property, applies only to RGB and YUV input modes and
+ can be omitted for BT.656 input modes
+
+ de-active:
+ description: |
+ Optional property, applies only to RGB and YUV input modes and
+ can be omitted for BT.656 input modes
+
+ hsync-active:
+ description: |
+ Optional property, applies only to RGB and YUV input modes and
+ can be omitted for BT.656 input modes
+
+ vsync-active:
+ description: |
+ Optional property, applies only to RGB and YUV input modes and
+ can be omitted for BT.656 input modes
+
+required:
+ - compatible
+ - reg
+
+examples:
+ - |
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel: display@0 {
+ compatible = "dlink,dir-685-panel", "ilitek,ili9322";
+ reg = <0>;
+ vcc-supply = <&vdisp>;
+ iovcc-supply = <&vdisp>;
+ vci-supply = <&vdisp>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+ };
+
+...
--
2.20.1
