Re: [PATCH 4/4] ARM: dts: Add LCD panel sharp ls037v7dw01 support for omap3-evm and ldp

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




* Tony Lindgren <tony@xxxxxxxxxxx> [140509 08:38]:
> * Tomi Valkeinen <tomi.valkeinen@xxxxxx> [140509 00:08]:
> > On 09/05/14 02:36, Tony Lindgren wrote:
> > Why always-on?
> 
> Oops, yeah that should not be there. The GPIO is board specific.

Oops, on ldp the regulator is always on tps61130rsa enabled by
twl4030 regen. Here's the updated patch with ldp support fixed
for the GPIOs tested with blank and bl_power.

Regards,

Tony

8< ------------------
From: Tony Lindgren <tony@xxxxxxxxxxx>
Date: Thu, 8 May 2014 17:55:32 -0700
Subject: [PATCH] ARM: dts: Add LCD panel sharp ls037v7dw01 support for omap3-evm and ldp

Looks like quite a few omap3 boards have sharp ls037v7dw01 that's
configured as various panel dpi entries for whatever legacy reasons.
For device tree based support, let's just configure these properly for
panel ls037v7dw01 instead of panel dpi.

This patch creates a common file for panel ls037v7dw01, and makes
boards ldp and omap3-evm to use it. The panel for ldp is configured
in the qvga mode and omap3-evm panel in vga mode.

The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen
controller for the omaps, so let's add a basic configuration for
the touchscreen also using the default values.

Note that we can now remove the regulator-name = "vdds_dsi"
entry for ldp, that's no longer needed as we have the entry
for vdds_dsi-supply = <&vpll2>.

Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>

--- a/arch/arm/boot/dts/omap3-evm-37xx.dts
+++ b/arch/arm/boot/dts/omap3-evm-37xx.dts
@@ -26,7 +26,44 @@
 	};
 };
 
+&dss {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&dss_dpi_pins1
+		&dss_dpi_pins2
+	>;
+};
+
 &omap3_pmx_core {
+	dss_dpi_pins1: pinmux_dss_dpi_pins2 {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
+
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
+
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3)   /* dss_data18.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3)   /* dss_data19.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3)   /* dss_data20.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3)   /* dss_data21.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3)   /* dss_data22.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3)   /* dss_data23.dss_data5 */
+		>;
+	};
+
 	mmc1_pins: pinmux_mmc1_pins {
 		pinctrl-single,pins = <
 			0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
@@ -75,6 +112,19 @@
 	};
 };
 
+&omap3_pmx_wkup {
+	dss_dpi_pins2: pinmux_dss_dpi_pins1 {
+		pinctrl-single,pins = <
+			0x0a (PIN_OUTPUT | MUX_MODE3)   /* sys_boot0.dss_data18 */
+			0x0c (PIN_OUTPUT | MUX_MODE3)   /* sys_boot1.dss_data19 */
+			0x10 (PIN_OUTPUT | MUX_MODE3)   /* sys_boot3.dss_data20 */
+			0x12 (PIN_OUTPUT | MUX_MODE3)   /* sys_boot4.dss_data21 */
+			0x14 (PIN_OUTPUT | MUX_MODE3)   /* sys_boot5.dss_data22 */
+			0x16 (PIN_OUTPUT | MUX_MODE3)   /* sys_boot6.dss_data23 */
+		>;
+	};
+};
+
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
--- a/arch/arm/boot/dts/omap3-evm-common.dtsi
+++ b/arch/arm/boot/dts/omap3-evm-common.dtsi
@@ -44,6 +44,11 @@
 
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
+#include "omap3-panel-sharp-ls037v7dw01.dtsi"
+
+&backlight0 {
+	gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>;
+};
 
 &i2c2 {
 	clock-frequency = <400000>;
@@ -61,6 +66,32 @@
 	};
 };
 
+&lcd_3v3 {
+	gpio = <&gpio5 25 GPIO_ACTIVE_LOW>;	/* gpio153 */
+	enable-active-low;
+};
+
+&lcd0 {
+	enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>;	/* gpio152, lcd INI */
+	reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;	/* gpio155, lcd RESB */
+	/*
+	 * The LCD is sideways, so we want the VGA mode instead of
+	 * QVGA mode. Probably also want to have omapfb.rotate=3
+	 * in the kernel cmdline until there's a binding for that.
+	 */
+	mode-gpios = <&gpio5 26 GPIO_ACTIVE_LOW		/* gpio154, lcd MO */
+		      &gpio1 2 GPIO_ACTIVE_HIGH		/* gpio2, lcd LR */
+		      &gpio1 3 GPIO_ACTIVE_HIGH>;	/* gpio3, lcd UD */
+};
+
+&mcspi1 {
+	tsc2046@0 {
+		interrupt-parent = <&gpio6>;
+		interrupts = <15 0>;		/* gpio175 */
+		pendown-gpio = <&gpio6 15 0>;
+	};
+};
+
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
 	vmmc_aux-supply = <&vsim>;
--- a/arch/arm/boot/dts/omap3-ldp.dts
+++ b/arch/arm/boot/dts/omap3-ldp.dts
@@ -164,6 +164,11 @@
 
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
+#include "omap3-panel-sharp-ls037v7dw01.dtsi"
+
+&backlight0 {
+	gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
+};
 
 &i2c2 {
 	clock-frequency = <400000>;
@@ -173,6 +178,25 @@
 	clock-frequency = <400000>;
 };
 
+/* tps61130rsa enabled by twl4030 regen */
+&lcd_3v3 {
+	regulator-always-on;
+};
+
+&lcd0 {
+	enable-gpios = <&twl_gpio 15 GPIO_ACTIVE_HIGH>;	/* lcd INI */
+	reset-gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;	/* gpio55, lcd RESB */
+	mode-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;	/* gpio56, lcd MO */
+};
+
+&mcspi1 {
+	tsc2046@0 {
+		interrupt-parent = <&gpio2>;
+		interrupts = <22 0>;		/* gpio54 */
+		pendown-gpio = <&gpio2 22 0>;
+	};
+};
+
 &mmc1 {
 	/* See 35xx errata 2.1.1.128 in SPRZ278F */
 	compatible = "ti,omap3-pre-es3-hsmmc";
@@ -251,8 +275,3 @@
 	/* Needed for ads7846 */
         regulator-name = "vcc";
 };
-
-&vpll2 {
-       /* Needed for DSS */
-       regulator-name = "vdds_dsi";
-};
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-panel-sharp-ls037v7dw01.dtsi
@@ -0,0 +1,67 @@
+/*
+ * Common file for omap dpi panels with QVGA and reset pins
+ *
+ * Note that the board specifc DTS file needs to specify
+ * at minimum the GPIO enable-gpios for display, and
+ * gpios for gpio-backlight.
+ */
+
+/ {
+	aliases {
+		display0 = &lcd0;
+	};
+
+	backlight0: backlight {
+		compatible = "gpio-backlight";
+		default-on;
+	};
+
+	/* 3.3V GPIO controlled regulator for LCD_ENVDD */
+	lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <70000>;
+	};
+
+	lcd0: display {
+		compatible = "sharp,ls037v7dw01";
+		label = "lcd";
+		power-supply = <&lcd_3v3>;
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+	};
+};
+
+&dss {
+	status = "ok";
+	vdds_dsi-supply = <&vpll2>;
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <18>;
+		};
+	};
+};
+
+&mcspi1 {
+	tsc2046@0 {
+		reg = <0>;			/* CS0 */
+		compatible = "ti,tsc2046";
+		spi-max-frequency = <1000000>;
+		vcc-supply = <&lcd_3v3>;
+		ti,x-min = /bits/ 16 <0>;
+		ti,x-max = /bits/ 16 <8000>;
+		ti,y-min = /bits/ 16 <0>;
+		ti,y-max = /bits/ 16 <4800>;
+		ti,x-plate-ohms = /bits/ 16 <40>;
+		ti,pressure-max = /bits/ 16 <255>;
+		ti,swap-xy;
+		linux,wakeup;
+	};
+};
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux