BTCOEX feature is not supported by all QCA4019 chipsets.
Since btcoex enabled by default in firmware, host needs to
enable COEX support depends on the hardware. Enabling it
by default in unsupported hardware will cause some
feature disabled in hardware.
This patch will read btcoex_support flag and
wlan priority gpio pin number from DT. Depends on the
btcoex_support flag value host will expose BTCOEX support
and wlan priority gpio pin number to target.
Testing:
* Tested HW : QCA4019
* Tested FW : 10.4-3.2.1.1-00017
Signed-off-by: Tamizh Chelvam <tamizhr@xxxxxxxxxxxxxx>
---
v2:
* Changed coex_support to bool type
drivers/net/wireless/ath/ath10k/core.c | 44 ++++++++++++++++++++++++++++++++-
drivers/net/wireless/ath/ath10k/core.h | 3 +++
drivers/net/wireless/ath/ath10k/debug.c | 3 +++
drivers/net/wireless/ath/ath10k/mac.c | 3 ++-
drivers/net/wireless/ath/ath10k/wmi.c | 2 +-
5 files changed, 52 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 5ec16ce..5712e28 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -2119,6 +2119,40 @@ static int ath10k_download_cal_data(struct ath10k *ar)
return 0;
}
+static void ath10k_core_fetch_btcoex_dt(struct ath10k *ar)
+{
+ struct device_node *node;
+ u8 coex_support = 0;
+ int ret;
+
+ node = ar->dev->of_node;
+ if (!node)
+ goto out;
+
+ ret = of_property_read_u8(node, "qcom,coexist-support", &coex_support);
+ if (ret) {
+ ar->coex_support = true;
+ goto out;
+ }
+
+ if (coex_support) {
+ ar->coex_support = true;
+ } else {
+ ar->coex_support = false;
+ ar->coex_gpio_pin = -1;
+ goto out;
+ }
+
+ ret = of_property_read_u32(node, "qcom,coexist-gpio-pin",
+ &ar->coex_gpio_pin);
+ if (ret)
+ ar->coex_gpio_pin = -1;
+
+out:
+ ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot coex_support %d coex_gpio_pin %d\n",
+ ar->coex_support, ar->coex_gpio_pin);
+}
+
static int ath10k_init_uart(struct ath10k *ar)
{
int ret;
@@ -2696,14 +2730,22 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode,
if (test_bit(WMI_SERVICE_BSS_CHANNEL_INFO_64, ar->wmi.svc_map))
val |= WMI_10_4_BSS_CHANNEL_INFO_64;
+ ath10k_core_fetch_btcoex_dt(ar);
+
/* 10.4 firmware supports BT-Coex without reloading firmware
* via pdev param. To support Bluetooth coexistence pdev param,
* WMI_COEX_GPIO_SUPPORT of extended resource config should be
* enabled always.
+ *
+ * We can still enable BTCOEX if firmware has the support
+ * eventhough btceox_support value is
+ * ATH10K_DT_BTCOEX_NOT_FOUND
*/
+
if (test_bit(WMI_SERVICE_COEX_GPIO, ar->wmi.svc_map) &&
test_bit(ATH10K_FW_FEATURE_BTCOEX_PARAM,
- ar->running_fw->fw_file.fw_features))
+ ar->running_fw->fw_file.fw_features) &&
+ ar->coex_support)
val |= WMI_10_4_COEX_GPIO_SUPPORT;
if (test_bit(WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY,
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 5101bf2..edf314e 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -1222,6 +1222,9 @@ struct ath10k {
struct ath10k_bus_params bus_param;
struct completion peer_delete_done;
+ bool coex_support;
+ int coex_gpio_pin;
+
/* must be last */
u8 drv_priv[0] __aligned(sizeof(void *));
};
diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c
index e000677..3894b77 100644
--- a/drivers/net/wireless/ath/ath10k/debug.c
+++ b/drivers/net/wireless/ath/ath10k/debug.c
@@ -1978,6 +1978,9 @@ static ssize_t ath10k_write_btcoex(struct file *file,
if (strtobool(buf, &val) != 0)
return -EINVAL;
+ if (!ar->coex_support)
+ return -EOPNOTSUPP;
+
mutex_lock(&ar->conf_mutex);
if (ar->state != ATH10K_STATE_ON &&
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 7fee35f..ac3ad5c 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -4982,7 +4982,8 @@ static int ath10k_start(struct ieee80211_hw *hw)
param = ar->wmi.pdev_param->enable_btcoex;
if (test_bit(WMI_SERVICE_COEX_GPIO, ar->wmi.svc_map) &&
test_bit(ATH10K_FW_FEATURE_BTCOEX_PARAM,
- ar->running_fw->fw_file.fw_features)) {
+ ar->running_fw->fw_file.fw_features) &&
+ ar->coex_support) {
ret = ath10k_wmi_pdev_set_param(ar, param, 0);
if (ret) {
ath10k_warn(ar,
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 61885d4..e76e365 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -8787,7 +8787,7 @@ static int ath10k_wmi_10_4_op_get_vdev_subtype(struct ath10k *ar,
cmd = (struct wmi_ext_resource_config_10_4_cmd *)skb->data;
cmd->host_platform_config = __cpu_to_le32(type);
cmd->fw_feature_bitmap = __cpu_to_le32(fw_feature_bitmap);
- cmd->wlan_gpio_priority = __cpu_to_le32(-1);
+ cmd->wlan_gpio_priority = __cpu_to_le32(ar->coex_gpio_pin);
cmd->coex_version = __cpu_to_le32(WMI_NO_COEX_VERSION_SUPPORT);
cmd->coex_gpio_pin1 = __cpu_to_le32(-1);
cmd->coex_gpio_pin2 = __cpu_to_le32(-1);
--
1.9.1
