This adds documentation about the newly introduced, optional
"xlnx,addrwidth" property to the binding documentation.
While at it, clarify the wording on some properties, replace obsolete
.txt file references with their new .yaml counterparts, and add a more
modern example, using the axistream-connected property.
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
---
.../bindings/net/xilinx_axienet.txt | 57 ++++++++++++++++---
1 file changed, 50 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt
index 7360617cdedb..78c278c5200f 100644
--- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt
+++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt
@@ -12,7 +12,8 @@ sent and received through means of an AXI DMA controller. This driver
includes the DMA driver code, so this driver is incompatible with AXI DMA
driver.
-For more details about mdio please refer phy.txt file in the same directory.
+For more details about mdio please refer to the ethernet-phy.yaml file in
+the same directory.
Required properties:
- compatible : Must be one of "xlnx,axi-ethernet-1.00.a",
@@ -27,14 +28,14 @@ Required properties:
instead, and only the Ethernet core interrupt is optionally
specified here.
- phy-handle : Should point to the external phy device.
- See ethernet.txt file in the same directory.
-- xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware
+ See the ethernet-controller.yaml file in the same directory.
+- xlnx,rxmem : Size of the RXMEM buffer in the hardware, in bytes.
Optional properties:
-- phy-mode : See ethernet.txt
+- phy-mode : See ethernet-controller.yaml.
- xlnx,phy-type : Deprecated, do not use, but still accepted in preference
to phy-mode.
-- xlnx,txcsum : 0 or empty for disabling TX checksum offload,
+- xlnx,txcsum : 0 for disabling TX checksum offload (default if omitted),
1 to enable partial TX checksum offload,
2 to enable full TX checksum offload
- xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload
@@ -48,10 +49,20 @@ Optional properties:
If this is specified, the DMA-related resources from that
device (DMA registers and DMA TX/RX interrupts) rather
than this one will be used.
- - mdio : Child node for MDIO bus. Must be defined if PHY access is
+- mdio : Child node for MDIO bus. Must be defined if PHY access is
required through the core's MDIO interface (i.e. always,
unless the PHY is accessed through a different bus).
+Required properties for axistream-connected subnode:
+- reg : Address and length of the AXI DMA controller MMIO space.
+- interrupts : A list of 2 interrupts: TX DMA and RX DMA, in that order.
+
+Optional properties for axistream-connected subnode:
+- xlnx,addrwidth: Specifies the configured address width of the DMA. Newer
+ versions of the IP allow setting this to a value between
+ 32 and 64. Defaults to 32 bits if not specified.
+
+
Example:
axi_ethernet_eth: ethernet@40c00000 {
compatible = "xlnx,axi-ethernet-1.00.a";
@@ -60,7 +71,7 @@ Example:
interrupts = <2 0 1>;
clocks = <&axi_clk>;
phy-mode = "mii";
- reg = <0x40c00000 0x40000 0x50c00000 0x40000>;
+ reg = <0x40c00000 0x40000>, <0x50c00000 0x40000>;
xlnx,rxcsum = <0x2>;
xlnx,rxmem = <0x800>;
xlnx,txcsum = <0x2>;
@@ -74,3 +85,35 @@ Example:
};
};
};
+ -----------------
+ axi_ethernet_eth: ethernet@7fe00000 {
+ compatible = "acme,fpga-ethernet", "xlnx,axi-ethernet-1.00.a";
+ reg = <0 0x7fe00000 0 0x40000>;
+ interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&soc_refclk100mhz>;
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy0>;
+
+ xlnx,rxmem = <4096>;
+ axistream-connected = <&axi_dma_eth>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ axi_dma_eth: axi_dma_ethernet@7fe40000 {
+ reg = <0 0x7fe40000 0 0x10000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ xlnx,addrwidth = <40>;
+ };
+
+ axi_ethernetlite_0_mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+ };
--
2.17.1
