On Thu, Dec 19, 2019 at 09:28:16AM -0800, Vasily Khoruzhick wrote: > This patchset adds driver for thermal sensor in A64, A83T, H3, H5, > H6 and R40 SoCs. > > v8: > - [vasily] Address more Maxime's comments for dt-schema > - [vasily] Add myself to MAINTAINERS for the driver and schema > - [vasily] Round calibration data size to word boundary for H6 and A64 > - [vasily] Change offset for A64 since it reports too low temp otherwise. > Likely conversion formula in user manual is not correct. > > v7: > - [vasily] Address Maxime's comments for dt-schema > - [vasily] Move common part of H3 and H5 dts into sunxi-h3-h5.dtsi > - [vasily] Add Maxime's a-b to the driver patch > > v6: > - [ondrej, vasily] Squash all driver related changes into a > single patch > - [ondrej] Rename calib -> calibration > - [ondrej] Fix thermal zone registration check > - [ondrej] Lower rate of sensor data interrupts to 4/sec/sensor > - [ondrej] Rework scale/offset values, H6 calibration > - [ondrej] Explicitly set mod clock to 24 MHz > - [ondrej] Set undocumented bits in CTRL0 for H6 > - [ondrej] Add support for A83T > - [ondrej] Add dts changes for A83T, H3, H5, H6 > - [vasily] Add dts changes for A64 > - [vasily] Address Maxime's comments for YAML scheme > - [vasily] Make .calc_temp callback mandatory > - [vasily] Set .max_register in regmap config, so regs can be > inspected using debugfs > > Ondrej Jirman (4): > ARM: dts: sun8i-a83t: Add thermal sensor and thermal zones > ARM: dts: sun8i-h3: Add thermal sensor and thermal zones > arm64: dts: allwinner: h5: Add thermal sensor and thermal zones > arm64: dts: allwinner: h6: Add thermal sensor and thermal zones > > Vasily Khoruzhick (1): > arm64: dts: allwinner: a64: Add thermal sensors and thermal zones > > Yangtao Li (2): > thermal: sun8i: add thermal driver for H6/H5/H3/A64/A83T/R40 > dt-bindings: thermal: add YAML schema for sun8i-thermal driver > bindings > > .../thermal/allwinner,sun8i-a83t-ths.yaml | 160 +++++ > MAINTAINERS | 8 + > arch/arm/boot/dts/sun8i-a83t.dtsi | 36 + > arch/arm/boot/dts/sun8i-h3.dtsi | 20 + > arch/arm/boot/dts/sunxi-h3-h5.dtsi | 6 + > arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 42 ++ > arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 26 + > arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 33 + > drivers/thermal/Kconfig | 14 + > drivers/thermal/Makefile | 1 + > drivers/thermal/sun8i_thermal.c | 639 ++++++++++++++++++ > 11 files changed, 985 insertions(+) > create mode 100644 Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml > create mode 100644 drivers/thermal/sun8i_thermal.c > > -- > 2.24.1 > Hello Thanks for your work. Tested-by: Corentin Labbe <clabbe.montjoie@xxxxxxxxx> Tested-on: sun50i-h6-pine-h64-model-b Tested-on: sun50i-h6-pine-h64 Tested-on: sun8i-a83t-bananapi-m3 Tested-on: sun8i-h2-plus-orangepi-zero Tested-on: sun8i-h2-plus-orangepi-r1 Tested-on: sun8i-h2-plus-libretech-all-h3-cc Tested-on: sun8i-h3-libretech-all-h3-cc Tested-on: sun50i-h5-libretech-all-h3-cc Tested-on: sun50i-a64-pine64-plus Note that your patch serie support R40 but you do not have any R40 DT patch. If you need testing, do not hesitate to ask. Regards
