Hi Alison,
Am 2019-12-10 06:35, schrieb Alison Wang:
Hi, Michael,
In most of our cases, TX and RX are using the same BCLK and SYNC
clocks. So the default synchronous mode (sync Rx with Tx) is used,
which means both transmitter and receiver will send and receive data
by following clocks of transmitter. It is verified on our boards.
I get that, but it doesn't make sense for the LS1028A SoC because, there
is no way you have have the TX data and the RX clocks or vice versa. The
hardware of the SoC doesn't allow that. I cannot speak of the QDS
variant
of the SoC, but the LS1028ARDB only has a transmitter. So there is no
problem, because it will default to the TX clock. But as soon as you
also
have a receiver you have to use the clock of the receiver block. You
could
say, use fsl,sai-synchronous-rx, but that will only work if the SAI is
used in RX mode. fsl,sai-asynchronous mode works for both on the other
hand and can therefore be the default mode.
-michael
Best Regards,
Alison Wang
-----Original Message-----
From: Shawn Guo <shawnguo@xxxxxxxxxx>
Sent: Monday, December 9, 2019 5:09 PM
To: Michael Walle <michael@xxxxxxxx>; Alison Wang
<alison.wang@xxxxxxx>
Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx;
linux-kernel@xxxxxxxxxxxxxxx; Leo Li <leoyang.li@xxxxxxx>; Rob Herring
<robh+dt@xxxxxxxxxx>; Mark Rutland <mark.rutland@xxxxxxx>
Subject: [EXT] Re: [PATCH] arm64: dts: ls1028a: put SAIs into async
mode
Caution: EXT Email
+ Alison Wang
On Fri, Nov 29, 2019 at 10:09:37PM +0100, Michael Walle wrote:
> The LS1028A SoC has only unidirectional SAIs. Therefore, it doesn't
> make sense to have the RX and TX part synchronous. Even worse, the RX
> part wont work out of the box because by default it is configured as
> synchronous to the TX part. And as said before, the pinmux of the SoC
> can only be configured to route either the RX or the TX signals to the
> SAI but never both at the same time. Thus configure the asynchronous
> mode by default.
>
> Signed-off-by: Michael Walle <michael@xxxxxxxx>
Alison, Leo,
Looks good to you?
Shawn
> ---
> arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> index 379913756e90..9be33426e5ce 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> @@ -637,6 +637,7 @@
> dma-names = "tx", "rx";
> dmas = <&edma0 1 4>,
> <&edma0 1 3>;
> + fsl,sai-asynchronous;
> status = "disabled";
> };
>
> @@ -651,6 +652,7 @@
> dma-names = "tx", "rx";
> dmas = <&edma0 1 6>,
> <&edma0 1 5>;
> + fsl,sai-asynchronous;
> status = "disabled";
> };
>
> @@ -665,6 +667,7 @@
> dma-names = "tx", "rx";
> dmas = <&edma0 1 8>,
> <&edma0 1 7>;
> + fsl,sai-asynchronous;
> status = "disabled";
> };
>
> @@ -679,6 +682,7 @@
> dma-names = "tx", "rx";
> dmas = <&edma0 1 10>,
> <&edma0 1 9>;
> + fsl,sai-asynchronous;
> status = "disabled";
> };
>
> @@ -693,6 +697,7 @@
> dma-names = "tx", "rx";
> dmas = <&edma0 1 12>,
> <&edma0 1 11>;
> + fsl,sai-asynchronous;
> status = "disabled";
> };
>
> @@ -707,6 +712,7 @@
> dma-names = "tx", "rx";
> dmas = <&edma0 1 14>,
> <&edma0 1 13>;
> + fsl,sai-asynchronous;
> status = "disabled";
> };
>
> --
> 2.20.1
>
