Use aliases nodes to easy kizbox dts readability.
Signed-off-by: Kamel Bouhara <kamel.bouhara@xxxxxxxxxxx>
---
Changes in v2:
- Fixed some missing aliases label from dtsi
arch/arm/boot/dts/at91-kizbox.dts | 172 ++++++++++++++---------------
arch/arm/boot/dts/at91sam9260.dtsi | 2 +-
2 files changed, 85 insertions(+), 89 deletions(-)
diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 90996eaf73b2..644009a157d6 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -28,85 +28,6 @@
};
};
- ahb {
- apb {
- tcb0: timer@fffa0000 {
- timer@0 {
- compatible = "atmel,tcb-timer";
- reg = <0>, <1>;
- };
-
- timer@2 {
- compatible = "atmel,tcb-timer";
- reg = <2>;
- };
- };
-
- macb0: ethernet@fffc4000 {
- phy-mode = "mii";
- pinctrl-0 = <&pinctrl_macb_rmii
- &pinctrl_macb_rmii_mii_alt>;
- status = "okay";
- };
-
- usart3: serial@fffd0000 {
- status = "okay";
- };
-
- dbgu: serial@fffff200 {
- status = "okay";
- };
-
- watchdog@fffffd40 {
- timeout-sec = <15>;
- atmel,max-heartbeat-sec = <16>;
- atmel,min-heartbeat-sec = <0>;
- status = "okay";
- };
- };
-
- usb0: ohci@500000 {
- num-ports = <1>;
- status = "okay";
- };
-
- ebi: ebi@10000000 {
- status = "okay";
-
- nand_controller: nand-controller {
- status = "okay";
- pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
- pinctrl-names = "default";
-
- nand@3 {
- reg = <0x3 0x0 0x800000>;
- rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
- nand-bus-width = <8>;
- nand-ecc-mode = "soft";
- nand-on-flash-bbt;
- label = "atmel_nand";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- bootstrap@0 {
- label = "bootstrap";
- reg = <0x0 0x20000>;
- };
-
- ubi@20000 {
- label = "ubi";
- reg = <0x20000 0x7fe0000>;
- };
- };
- };
- };
- };
- };
-
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
@@ -127,15 +48,6 @@
};
};
- i2c-gpio-0 {
- status = "okay";
-
- rtc: pcf8563@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- };
-
pwm_leds {
compatible = "pwm-leds";
@@ -179,3 +91,87 @@
&pinctrl_tcb1_tiob0>;
};
};
+
+&tcb0 {
+ timer@0 {
+ compatible = "atmel,tcb-timer";
+ reg = <0>, <1>;
+ };
+
+ timer@2 {
+ compatible = "atmel,tcb-timer";
+ reg = <2>;
+ };
+};
+
+&ebi {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
+ pinctrl-names = "default";
+
+ nand@3 {
+ reg = <0x3 0x0 0x800000>;
+ rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ label = "atmel_nand";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ bootstrap@0 {
+ label = "bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ ubi@20000 {
+ label = "ubi";
+ reg = <0x20000 0x7fe0000>;
+ };
+ };
+ };
+};
+
+&macb0 {
+ phy-mode = "mii";
+ pinctrl-0 = <&pinctrl_macb_rmii
+ &pinctrl_macb_rmii_mii_alt>;
+ status = "okay";
+};
+
+&usart3 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+};
+
+&watchdog {
+ timeout-sec = <15>;
+ atmel,max-heartbeat-sec = <16>;
+ atmel,min-heartbeat-sec = <0>;
+ status = "okay";
+};
+
+&usb0 {
+ num-ports = <1>;
+ status = "okay";
+};
+
+&i2c-gpio-0 {
+ status = "okay";
+
+ rtc: pcf8563@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index dee9c0c8a096..9f9ee3cd7375 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -738,7 +738,7 @@
status = "disabled";
};
- watchdog@fffffd40 {
+ watchdog: watchdog@fffffd40 {
compatible = "atmel,at91sam9260-wdt";
reg = <0xfffffd40 0x10>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
--
2.24.0
