On Mon, Dec 2, 2019 at 9:17 AM Adam Ford <aford173@xxxxxxxxx> wrote:
>
> On Mon, Dec 2, 2019 at 8:28 AM Philipp Zabel <p.zabel@xxxxxxxxxxxxxx> wrote:
> >
> > On Fri, 2019-11-29 at 17:41 -0600, Adam Ford wrote:
> > > The technical reference manual for both the i.MX8MQ and i.MX8M Mini
> > > appear to show the same register definitions and locations for the
> > > General Power Controller (GPC).
> > >
> > > This patch expands the table of compatible SoC's to include
> > > the i.MX8m Mini
> > >
> > > Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
> > >
> > > diff --git a/drivers/soc/imx/gpcv2.c b/drivers/soc/imx/gpcv2.c
> > > index b0dffb06c05d..67c54cbb6c81 100644
> > > --- a/drivers/soc/imx/gpcv2.c
> > > +++ b/drivers/soc/imx/gpcv2.c
> > > @@ -641,6 +641,7 @@ static int imx_gpcv2_probe(struct platform_device *pdev)
> > > static const struct of_device_id imx_gpcv2_dt_ids[] = {
> > > { .compatible = "fsl,imx7d-gpc", .data = &imx7_pgc_domain_data, },
> > > { .compatible = "fsl,imx8mq-gpc", .data = &imx8m_pgc_domain_data, },
> > > + { .compatible = "fsl,imx8mm-gpc", .data = &imx8m_pgc_domain_data, },
> >
> > According to the 5.2.5.1 "PGC power domains" chapters in both the i.MX
> > 8M Dual/8M QuadLite/8M Quad and i.MX 8M Mini Applications Processor
> > Reference Manuals (Rev.1), the two SoCs have a different list of power
> > domains:
>
> Shoot. I needed to go further down in the table. I stopped after the
> first four.
>
> Sorry for the noise.
>
> adam
> >
> > i.MX8MQ:
> > PGC_C0
> > PGC_C1
> > PGC_C2
> > PGC_C3
> > PGC_SCU
> > PGC_MF
> > PGC_OTG1
> > PGC_OTG2
> > PGC_PCIE
> > PGC_MIPI
> > PGC_DDR1
> > PGC_DDR2
> > PGC_VPU
> > PGC_GPU
> > PGC_HDMI
> > PGC_DISP
> > PGC_MIPI_CSI1
> > PGC_MIPI_CSI2
> > PGC_PCIE2
> >
> > i.MX8MM:
> > PGC_C0
> > PGC_C1
> > PGC_C2
> > PGC_C3
> > PGC_SCU
> > PGC_NOC
> > PGC_PCIE
> > PGC_OTG1
> > PGC_OTG2
> > PGC_DDR1
> > PGC_DISPMIX
> > GPC_MIPI
> > PGC_GPUMIX
> > PGC_GPU_3D
> > PGC_GPU_2D
> > PGC_VPUMIX
> > PGC_VPU_G1
> > PGC_VPU_G2
> > PGC_VPU_H1
Philipp,
Thanks for reviewing it and catching my mistake.
I went though the datasheet more thoroughly, and I think I have the
table correct for the i.MX8M Mini. With that and a small tweak to the
OTG nodes, I was able to use USB OTG1 and OTG2 ports.
I am going to submit a V2 fix tomorrow after I clean it up. I'll do a
multi-part series where part 1 is the GPC, part 2 will be the OTG
updates, and if I get more peripherals working, I'll add them as
additional parts to the series.
adam
> >
> > regards
> > Philipp
> >
