On 04/27/2014 03:50 AM, YoungJun Cho wrote: > This patch adds DT bindings for s6e3fa0 panel. > The bindings describes panel resources, display timings and cpu mode timings. > > Changelog v2: > - Adds unit address (commented by Sachin Kamat) > Changelog v3: > - Removes optional delay, size properties (commented by Laurent Pinchart) > - Adds OLED detection, TE gpio properties > Changelog v4: > - Moves CPU timings relevant properties from FIMD DT > (commeted by Laurent Pinchart, Andrzej Hajda) > Changelog v5: > - Fixes gpio property names (commented by Andrzej Hajda) > Changelog v6: > - Renames CPU timings to CPU mode timings > - Modifies CPU mode timings internal properties relevant things > (commeted by Laurent Pinchart, Andrzej Hajda) > > Signed-off-by: YoungJun Cho <yj44.cho@xxxxxxxxxxx> > Acked-by: Inki Dae <inki.dae@xxxxxxxxxxx> > Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx> > --- > .../devicetree/bindings/panel/samsung,s6e3fa0.txt | 68 ++++++++++++++++++++ > 1 file changed, 68 insertions(+) > create mode 100644 Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt > > diff --git a/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt b/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt > new file mode 100644 > index 0000000..9f06645 > --- /dev/null > +++ b/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt > @@ -0,0 +1,68 @@ > +Samsung S6E3FA0 AMOLED LCD 5.7 inch panel > + > +Required properties: > + - compatible: "samsung,s6e3fa0" > + - reg: the virtual channel number of a DSI peripheral > + - vdd3-supply: core voltage supply > + - vci-supply: voltage supply for analog circuits > + - reset-gpios: a GPIO spec for the reset pin > + - det-gpios: a GPIO spec for the OLED detection pin > + - te-gpios: a GPIO spec for the TE pin > + - display-timings: timings for the connected panel as described by [1] This still bothers me, it forces users to provide bunch of fake properties (four porches, two syncs and clock-frequency) just because we need to pass somehow pixel width and height. And do we really need pixel dimension to be passed via DT? I guess it could be: - hardcoded into the driver, - derived from the panel id, - maybe read from the panel, this is the best option I guess but I am not sure if panel provides an API for this. Regards Andrzej > + - cpu-mode-timings: CPU interface timings for the connected panel, > + and it contains following properties. > + Required properties: > + - wr-active: clock cycles for the active period of CS enable in CPU > + interface. > + Optional properties: > + - cs-setup: clock cycles for the active period of address signal > + enable until chip select is enable in CPU interface. > + If not specified, the default value(0) will be used. > + - wr-setup: clock cycles for the active period of CS signal enable > + until write signal is enable in CPU interface. > + If not specified, the default value(0) will be used. > + - wr-hold: clock cycles for the active period of CS disable until > + write signal is disable in CPU interface. > + If not specified, the default value(0) will be used. > + > +Optional properties: > + > +The device node can contain one 'port' child node with one child 'endpoint' > +node, according to the bindings defined in [2]. This node should describe > +panel's video bus. > + > +[1]: Documentation/devicetree/bindings/video/display-timing.txt > +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt > + > +Example: > + > + panel@0 { > + compatible = "samsung,s6e3fa0"; > + reg = <0>; > + vdd3-supply = <&vcclcd_reg>; > + vci-supply = <&vlcd_reg>; > + reset-gpios = <&gpy7 4 0>; > + det-gpios = <&gpg0 6 0>; > + te-gpios = <&gpd1 7 0>; > + > + display-timings { > + timing0: timing-0 { > + clock-frequency = <0>; > + hactive = <1080>; > + vactive = <1920>; > + hfront-porch = <2>; > + hback-porch = <2>; > + hsync-len = <1>; > + vfront-porch = <1>; > + vback-porch = <4>; > + vsync-len = <1>; > + }; > + }; > + > + cpu-mode-timings { > + cs-setup = <0>; > + wr-setup = <0>; > + wr-active = <1>; > + wr-hold = <0>; > + }; > + }; > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html