This patch adds DT bindings for s6e3fa0 panel.
The bindings describes panel resources, display timings and cpu mode timings.
Changelog v2:
- Adds unit address (commented by Sachin Kamat)
Changelog v3:
- Removes optional delay, size properties (commented by Laurent Pinchart)
- Adds OLED detection, TE gpio properties
Changelog v4:
- Moves CPU timings relevant properties from FIMD DT
(commeted by Laurent Pinchart, Andrzej Hajda)
Changelog v5:
- Fixes gpio property names (commented by Andrzej Hajda)
Changelog v6:
- Renames CPU timings to CPU mode timings
- Modifies CPU mode timings internal properties relevant things
(commeted by Laurent Pinchart, Andrzej Hajda)
Signed-off-by: YoungJun Cho <yj44.cho@xxxxxxxxxxx>
Acked-by: Inki Dae <inki.dae@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
---
.../devicetree/bindings/panel/samsung,s6e3fa0.txt | 68 ++++++++++++++++++++
1 file changed, 68 insertions(+)
create mode 100644 Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt
diff --git a/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt b/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt
new file mode 100644
index 0000000..9f06645
--- /dev/null
+++ b/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt
@@ -0,0 +1,68 @@
+Samsung S6E3FA0 AMOLED LCD 5.7 inch panel
+
+Required properties:
+ - compatible: "samsung,s6e3fa0"
+ - reg: the virtual channel number of a DSI peripheral
+ - vdd3-supply: core voltage supply
+ - vci-supply: voltage supply for analog circuits
+ - reset-gpios: a GPIO spec for the reset pin
+ - det-gpios: a GPIO spec for the OLED detection pin
+ - te-gpios: a GPIO spec for the TE pin
+ - display-timings: timings for the connected panel as described by [1]
+ - cpu-mode-timings: CPU interface timings for the connected panel,
+ and it contains following properties.
+ Required properties:
+ - wr-active: clock cycles for the active period of CS enable in CPU
+ interface.
+ Optional properties:
+ - cs-setup: clock cycles for the active period of address signal
+ enable until chip select is enable in CPU interface.
+ If not specified, the default value(0) will be used.
+ - wr-setup: clock cycles for the active period of CS signal enable
+ until write signal is enable in CPU interface.
+ If not specified, the default value(0) will be used.
+ - wr-hold: clock cycles for the active period of CS disable until
+ write signal is disable in CPU interface.
+ If not specified, the default value(0) will be used.
+
+Optional properties:
+
+The device node can contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in [2]. This node should describe
+panel's video bus.
+
+[1]: Documentation/devicetree/bindings/video/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+ panel@0 {
+ compatible = "samsung,s6e3fa0";
+ reg = <0>;
+ vdd3-supply = <&vcclcd_reg>;
+ vci-supply = <&vlcd_reg>;
+ reset-gpios = <&gpy7 4 0>;
+ det-gpios = <&gpg0 6 0>;
+ te-gpios = <&gpd1 7 0>;
+
+ display-timings {
+ timing0: timing-0 {
+ clock-frequency = <0>;
+ hactive = <1080>;
+ vactive = <1920>;
+ hfront-porch = <2>;
+ hback-porch = <2>;
+ hsync-len = <1>;
+ vfront-porch = <1>;
+ vback-porch = <4>;
+ vsync-len = <1>;
+ };
+ };
+
+ cpu-mode-timings {
+ cs-setup = <0>;
+ wr-setup = <0>;
+ wr-active = <1>;
+ wr-hold = <0>;
+ };
+ };
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
