Add nodes for DWC3 USB controller, QMP and QUSB PHYs.
Signed-off-by: Sandeep Maheswaram <sanm@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7180-idp.dts | 25 ++++++++
arch/arm64/boot/dts/qcom/sc7180.dtsi | 104 ++++++++++++++++++++++++++++++++
2 files changed, 129 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 189254f..aecc994 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -400,3 +400,28 @@
bias-pull-up;
};
};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+ vdd-supply = <&vreg_l4a_0p8>;
+ vdda-pll-supply = <&vreg_l11a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l17a_3p0>;
+ qcom,imp-res-offset-value = <8>;
+ qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+ qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+ qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+ vdda-phy-supply = <&vreg_l3c_1p2>;
+ vdda-pll-supply = <&vreg_l4a_0p8>;
+};
\ No newline at end of file
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index cb623b7..7ee068f 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/phy/phy-qcom-qusb2.h>
/ {
interrupt-parent = <&intc>;
@@ -184,6 +185,17 @@
#power-domain-cells = <1>;
};
+ qfprom@784000 {
+ compatible = "qcom,qfprom";
+ reg = <0 0x00784000 0 0x8ff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qusb2p_hstx_trim: hstx-trim-primary@25b {
+ reg = <0x25b 0x1>;
+ bits = <1 3>;
+ };
+ };
pdc: interrupt-controller@b220000 {
compatible = "qcom,sdm845-pdc";
reg = <0 0xb220000 0 0x30000>;
@@ -913,6 +925,98 @@
status = "disabled";
};
+ usb_1_hsphy: phy@88e3000 {
+ compatible = "qcom,sc7180-qusb2-phy";
+ reg = <0 0x088e3000 0 0x400>;
+ status = "disabled";
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "cfg_ahb","ref";
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+ nvmem-cells = <&qusb2p_hstx_trim>;
+ };
+
+ usb_1_qmpphy: phy@88e9000 {
+ compatible = "qcom,sc7180-qmp-usb3-phy";
+ reg = <0 0x088e9000 0 0x18c>,
+ <0 0x088e8000 0 0x38>;
+ reg-names = "reg-base", "dp_com";
+ status = "disabled";
+ #clock-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_PHY_PRIM_BCR>;
+ reset-names = "phy", "common";
+
+ usb_1_ssphy: lanes@88e9200 {
+ reg = <0 0x088e9200 0 0x128>,
+ <0 0x088e9400 0 0x200>,
+ <0 0x088e9c00 0 0x218>,
+ <0 0x088e9600 0 0x128>,
+ <0 0x088e9800 0 0x200>,
+ <0 0x088e9a00 0 0x18>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_phy_pipe_clk_src";
+ };
+ };
+
+ usb_1: usb@a6f8800 {
+ compatible = "qcom,sc7180-dwc3", "qcom,dwc3";
+ reg = <0 0x0a6f8800 0 0x400>;
+ status = "disabled";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <150000000>;
+
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ power-domains = <&gcc USB30_PRIM_GDSC>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+ usb_1_dwc3: dwc3@a600000 {
+ compatible = "snps,dwc3";
+ reg = <0 0x0a600000 0 0xe000>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x540 0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
spmi_bus: spmi@c440000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0 0xc440000 0 0x1100>,
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
