This patch adds the Device tree bindings for the Ethernet over SPI
protocol driver of the Qualcomm QCA7000 HomePlug GreenPHY.
Signed-off-by: Stefan Wahren <stefan.wahren@xxxxxxxx>
---
.../devicetree/bindings/net/qca-qca7000-spi.txt | 51 ++++++++++++++++++++
1 file changed, 51 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/qca-qca7000-spi.txt
diff --git a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt
new file mode 100644
index 0000000..132c10f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt
@@ -0,0 +1,51 @@
+* Qualcomm QCA7000 (Ethernet over SPI protocol)
+
+Note: The QCA7000 is useable as a SPI device. In this case it must be defined
+as a child of a spi master in the device tree.
+
+Required properties:
+- compatible : Should be "qca,qca7000"
+- reg : Should specify the SPI chip select
+- intr-gpios : Should specify the GPIO for SPI interrupt
+- spi-cpha : Must be set
+- spi-cpol: Must be set
+
+Optional properties:
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
+ Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing
+ the property will set the SPI frequency to 8000000 Hertz.
+- local-mac-address: 6 bytes, mac address
+- qca,legacy-mode : Should specify the data transfer mode of the QCA7000
+ (0 = burst mode, 1 = legacy mode). Missing the property will use the
+ burst mode.
+- linux,burst-length : Number of data bytes per burst. Numbers smaller than 1
+ or greater than 5000 are invalid. Missing the property will set the
+ burst length to 5000 bytes. This property has only an effect in burst mode.
+- linux,pluggable-connection : Should be set to skip signature check while
+ probing. This property is useful if the SPI master and QCA7000 are not on the
+ same board.
+
+Example:
+
+/* Freescale i.MX28 SPI master*/
+ssp2: ssp@80014000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ qca7000@0 {
+ compatible = "qca,qca7000";
+ reg = <0x0>;
+ spi-cpha; /* SPI mode: CPHA=1 */
+ spi-cpol; /* SPI mode: CPOL=1 */
+ spi-max-frequency = <8000000>; /* freq: 8 MHz */
+ intr-gpios = <&gpio3 25 0>; /* GPIO3_25 */
+ qca,legacy-mode = <0>; /* Burst mode */
+ local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
+ linux,burst-length = <5000>;
+ linux,pluggable-connection;
+ };
+};
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
