On Mon, Sep 23, 2019 at 12:15:13PM +0200, Kurt Kanzenbach wrote:
> From: Rasmus Villemoes <rasmus.villemoes@xxxxxxxxx>
>
> This adds Device Tree binding documentation for the external interrupt
> lines with configurable polarity present on some Layerscape SOCs.
>
> Signed-off-by: Rasmus Villemoes <rasmus.villemoes@xxxxxxxxx>
> Signed-off-by: Kurt Kanzenbach <kurt@xxxxxxxxxxxxx>
> ---
>
> Changes since v5:
>
> - Add #address-cells and #size-cells to parent
> - Mention LS2088A and the ISC unit
Repeating some of my lost comments from v2 2 years ago...
>
> .../interrupt-controller/fsl,ls-extirq.txt | 47 +++++++++++++++++++
> 1 file changed, 47 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/interrupt-controller/fsl,ls-extirq.txt
>
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-extirq.txt b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-extirq.txt
> new file mode 100644
> index 000000000000..7b53f9cc8019
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-extirq.txt
> @@ -0,0 +1,47 @@
> +* Freescale Layerscape external IRQs
> +
> +Some Layerscape SOCs (LS1021A, LS1043A, LS1046A, LS2088A) support
> +inverting the polarity of certain external interrupt lines.
> +
> +The device node must be a child of the node representing the
> +Supplemental Configuration Unit (SCFG) or the Interrupt Sampling
> +Control (ISC) Unit.
> +
> +Required properties:
> +- compatible: should be "fsl,<soc-name>-extirq", e.g. "fsl,ls1021a-extirq".
> +- interrupt-controller: Identifies the node as an interrupt controller
> +- #interrupt-cells: Must be 2. The first element is the index of the
> + external interrupt line. The second element is the trigger type.
> +- interrupt-parent: phandle of GIC.
> +- reg: Specifies the Interrupt Polarity Control Register (INTPCR) in the SCFG.
> +- fsl,extirq-map: Specifies the mapping to interrupt numbers in the parent
> + interrupt controller. Interrupts are mapped one-to-one to parent
> + interrupts.
This should be an 'interrupt-map' instead.
> +
> +Optional properties:
> +- fsl,bit-reverse: This boolean property should be set on the LS1021A
> + if the SCFGREVCR register has been set to all-ones (which is usually
> + the case), meaning that all reads and writes of SCFG registers are
> + implicitly bit-reversed. Other compatible platforms do not have such
> + a register.
Couldn't you just read that register and tell?
Does this apply to only the extirq register or all of scfg?
> +
> +Example:
> + scfg: scfg@1570000 {
> + compatible = "fsl,ls1021a-scfg", "syscon";
> + #address-cells = <1>;
> + #size-cells = <0>;
As the child node(s) are memory mapped, this should not be 0. And you
need 'ranges'.
> + ...
> + extirq: interrupt-controller {
> + compatible = "fsl,ls1021a-extirq";
> + #interrupt-cells = <2>;
> + interrupt-controller;
> + interrupt-parent = <&gic>;
> + reg = <0x1ac>;
> + fsl,extirq-map = <163 164 165 167 168 169>;
> + fsl,bit-reverse;
> + };
> + };
> +
> +
> + interrupts-extended = <&gic GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
> + <&extirq 1 IRQ_TYPE_LEVEL_LOW>;
> --
> 2.20.1
>
