On Thu, Sep 19, 2019 at 11:16:39AM +0200, Lars Poeschel wrote:
> This adds documentation about the uart phy to the pn532 binding doc. As
> the filename "pn533-i2c.txt" is not appropriate any more, rename it to
> the more general "pn532.txt".
> This also documents the deprecation of the compatible strings ending
> with "...-i2c".
>
> Cc: Johan Hovold <johan@xxxxxxxxxx>
> Cc: Simon Horman <horms@xxxxxxxxxxxx>
> Signed-off-by: Lars Poeschel <poeschel@xxxxxxxxxxx>
> ---
> Changes in v8:
> - Update existing binding doc instead of adding a new one:
> - Add uart phy example
> - Add general "pn532" compatible string
> - Deprecate "...-i2c" compatible strings
> - Rename file to a more general filename
> - Intentionally drop Rob's Reviewed-By as I guess this rather big change
> requires a new review
>
> Changes in v7:
> - Accidentally lost Rob's Reviewed-By
>
> Changes in v6:
> - Rebased the patch series on v5.3-rc5
> - Picked up Rob's Reviewed-By
>
> Changes in v4:
> - Add documentation about reg property in case of i2c
>
> Changes in v3:
> - seperate binding doc instead of entry in trivial-devices.txt
>
> .../devicetree/bindings/net/nfc/pn532.txt | 46 +++++++++++++++++++
> .../devicetree/bindings/net/nfc/pn533-i2c.txt | 29 ------------
> 2 files changed, 46 insertions(+), 29 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/net/nfc/pn532.txt
> delete mode 100644 Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt
In the future, use '-M' option (I recommend making this the default).
>
> diff --git a/Documentation/devicetree/bindings/net/nfc/pn532.txt b/Documentation/devicetree/bindings/net/nfc/pn532.txt
> new file mode 100644
> index 000000000000..f0591f160bee
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/nfc/pn532.txt
> @@ -0,0 +1,46 @@
> +* NXP Semiconductors PN532 NFC Controller
> +
> +Required properties:
> +- compatible: Should be
> + - "nxp,pn532" Place a node with this inside the devicetree node of the bus
> + where the NFC chip is connected to.
> + Currently the kernel has phy bindings for uart and i2c.
> + - "nxp,pn532-i2c" (DEPRECATED) only works for the i2c binding.
> + - "nxp,pn533-i2c" (DEPRECATED) only works for the i2c binding.
No more pm533 support?
> +
> +Required properties if connected on i2c:
> +- clock-frequency: I²C work frequency.
> +- reg: for the I²C bus address. This is fixed at 0x24 for the PN532.
> +- interrupts: GPIO interrupt to which the chip is connected
UART attached case has no irq? I guess it could just start sending
data...
> +
> +Optional SoC Specific Properties:
> +- pinctrl-names: Contains only one value - "default".
> +- pintctrl-0: Specifies the pin control groups used for this controller.
> +
> +Example (for ARM-based BeagleBone with PN532 on I2C2):
> +
> +&i2c2 {
> +
> +
> + pn532: pn532@24 {
nfc@24
> +
> + compatible = "nxp,pn532";
> +
> + reg = <0x24>;
> + clock-frequency = <400000>;
> +
> + interrupt-parent = <&gpio1>;
> + interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
> +
> + };
> +};
> +
> +Example (for PN532 connected via uart):
> +
> +uart4: serial@49042000 {
> + compatible = "ti,omap3-uart";
> +
> + pn532: nfc {
> + compatible = "nxp,pn532";
> + };
> +};
