On 19-09-19 10:24, Bartosz Golaszewski wrote:
> śr., 18 wrz 2019 o 14:06 Marco Felsch <m.felsch@xxxxxxxxxxxxxx> napisał(a):
> >
> > On 19-09-18 09:04, Bartosz Golaszewski wrote:
> > > wt., 17 wrz 2019 o 12:59 Marco Felsch <m.felsch@xxxxxxxxxxxxxx> napisał(a):
> > > >
> > > > The DA9062 is a mfd pmic device which supports 5 GPIOs. The GPIOs can
> > > > be used as input, output or have a special use-case.
> > > >
> > > > The patch adds the support for the normal input/output use-case.
> > > >
> > > > Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>
> > > > ---
> > > > drivers/gpio/Kconfig | 11 ++
> > > > drivers/gpio/Makefile | 1 +
> > > > drivers/gpio/gpio-da9062.c | 265 ++++++++++++++++++++++++++++++++
> > > > include/linux/mfd/da9062/gpio.h | 13 ++
> > > > 4 files changed, 290 insertions(+)
> > > > create mode 100644 drivers/gpio/gpio-da9062.c
> > > > create mode 100644 include/linux/mfd/da9062/gpio.h
> > > >
> > > > diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> > > > index bb13c266c329..b308ea549aaa 100644
> > > > --- a/drivers/gpio/Kconfig
> > > > +++ b/drivers/gpio/Kconfig
> > > > @@ -1038,6 +1038,17 @@ config GPIO_DA9055
> > > >
> > > > If driver is built as a module it will be called gpio-da9055.
> > > >
> > > > +config GPIO_DA9062
> > > > + tristate "Dialog Semiconductor DA9062 GPIO"
> > > > + depends on MFD_DA9062
> > > > + help
> > > > + Say yes here to enable the GPIO driver for the DA9062 chip.
> > > > +
> > > > + The Dialog DA9062 PMIC chip has 5 GPIO pins that can be
> > > > + be controller by this driver.
> > > > +
> > > > + If driver is built as a module it will be called gpio-da9062.
> > > > +
> > > > config GPIO_DLN2
> > > > tristate "Diolan DLN2 GPIO support"
> > > > depends on MFD_DLN2
> > > > diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> > > > index a4e91175c708..f29c8af2d096 100644
> > > > --- a/drivers/gpio/Makefile
> > > > +++ b/drivers/gpio/Makefile
> > > > @@ -45,6 +45,7 @@ obj-$(CONFIG_GPIO_CRYSTAL_COVE) += gpio-crystalcove.o
> > > > obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o
> > > > obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
> > > > obj-$(CONFIG_GPIO_DA9055) += gpio-da9055.o
> > > > +obj-$(CONFIG_GPIO_DA9062) += gpio-da9062.o
> > > > obj-$(CONFIG_GPIO_DAVINCI) += gpio-davinci.o
> > > > obj-$(CONFIG_GPIO_DLN2) += gpio-dln2.o
> > > > obj-$(CONFIG_GPIO_DWAPB) += gpio-dwapb.o
> > > > diff --git a/drivers/gpio/gpio-da9062.c b/drivers/gpio/gpio-da9062.c
> > > > new file mode 100644
> > > > index 000000000000..6035963929a2
> > > > --- /dev/null
> > > > +++ b/drivers/gpio/gpio-da9062.c
> > > > @@ -0,0 +1,265 @@
> > > > +// SPDX-License-Identifier: GPL-2.0
> > > > +/*
> > > > + * GPIO Driver for Dialog DA9062 PMICs.
> > > > + * Based on DA9055 GPIO driver.
> > > > + *
> > > > + * Copyright (C) 2019 Pengutronix, Marco Felsch <kernel@xxxxxxxxxxxxxx>
> > > > + */
> > > > +#include <linux/module.h>
> > > > +#include <linux/platform_device.h>
> > > > +#include <linux/regmap.h>
> > > > +
> > > > +#include <linux/gpio/driver.h>
> > > > +#include <linux/gpio/consumer.h>
> > > > +
> > > > +#include <linux/mfd/da9062/core.h>
> > > > +#include <linux/mfd/da9062/registers.h>
> > > > +
> > > > +#include "gpiolib.h"
> > > > +
> > > > +#define DA9062_TYPE(offset) (4 * (offset % 2))
> > > > +#define DA9062_PIN_SHIFT(offset) (4 * (offset % 2))
> > > > +#define DA9062_PIN_ALTERNATE 0x00 /* gpio alternate mode */
> > > > +#define DA9062_PIN_GPI 0x01 /* gpio in */
> > > > +#define DA9062_PIN_GPO_OD 0x02 /* gpio out open-drain */
> > > > +#define DA9062_PIN_GPO_PP 0x03 /* gpio out push-pull */
> > > > +#define DA9062_GPIO_NUM 5
> > > > +
> > > > +struct da9062_gpio {
> > > > + struct da9062 *da9062;
> > > > + struct gpio_chip gp;
> > > > +};
> > > > +
> > > > +int da9062_gpio_get_hwgpio(struct gpio_desc *desc)
> > > > +{
> > > > + return gpio_chip_hwgpio(desc);
> > > > +}
> > > > +EXPORT_SYMBOL_GPL(da9062_gpio_get_hwgpio);
> > > > +
> > >
> > > Is this going to be used anywhere? I'm not really a fan of adding new
> > > APIs without users.
> >
> > Yes, it is used here: https://lkml.org/lkml/2019/9/17/411
> >
> > I don't know if I should add the gpio here or as seperate patch within
> > the above series.
> >
> > > > +static int da9062_gpio_get_pin_mode(struct regmap *regmap, unsigned int offset)
> > > > +{
> > > > + int ret;
> > > > + int val;
> > >
> > > Nit: maybe put these two in a single line?
> >
> > Yes.
> >
> > > > +
> > > > + ret = regmap_read(regmap, DA9062AA_GPIO_0_1 + (offset >> 1), &val);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > +
> > > > + val >>= DA9062_PIN_SHIFT(offset);
> > > > + val &= DA9062AA_GPIO0_PIN_MASK;
> > > > +
> > > > + return val;
> > > > +}
> > > > +
> > > > +static int da9062_gpio_set_pin_mode(struct regmap *regmap, unsigned int offset,
> > > > + unsigned int mode)
> > > > +{
> > > > + unsigned int mask;
> > > > +
> > > > + mode &= DA9062AA_GPIO0_PIN_MASK;
> > > > + mode <<= DA9062_PIN_SHIFT(offset);
> > > > + mask = DA9062AA_GPIO0_PIN_MASK << DA9062_PIN_SHIFT(offset);
> > > > +
> > > > + return regmap_update_bits(regmap, DA9062AA_GPIO_0_1 + (offset >> 1),
> > > > + mask, mode);
> > > > +}
> > > > +
> > > > +static int da9062_gpio_get(struct gpio_chip *gc, unsigned int offset)
> > > > +{
> > > > + struct da9062_gpio *gpio = gpiochip_get_data(gc);
> > > > + struct regmap *regmap = gpio->da9062->regmap;
> > > > + int gpio_dir, val;
> > > > + int ret;
> > > > +
> > > > + gpio_dir = da9062_gpio_get_pin_mode(regmap, offset);
> > > > + if (gpio_dir < 0)
> > > > + return gpio_dir;
> > > > +
> > > > + switch (gpio_dir) {
> > > > + case DA9062_PIN_ALTERNATE:
> > > > + return -ENOTSUPP;
> > > > + case DA9062_PIN_GPI:
> > > > + ret = regmap_read(regmap, DA9062AA_STATUS_B, &val);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > + break;
> > > > + case DA9062_PIN_GPO_OD:
> > > > + /* falltrough */
> > > > + case DA9062_PIN_GPO_PP:
> > > > + ret = regmap_read(regmap, DA9062AA_GPIO_MODE0_4, &val);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > + }
> > > > +
> > > > + return val & BIT(offset);
> > > > +}
> > > > +
> > > > +static void da9062_gpio_set(struct gpio_chip *gc, unsigned int offset,
> > > > + int value)
> > > > +{
> > > > + struct da9062_gpio *gpio = gpiochip_get_data(gc);
> > > > + struct regmap *regmap = gpio->da9062->regmap;
> > > > +
> > > > + regmap_update_bits(regmap, DA9062AA_GPIO_MODE0_4, BIT(offset),
> > > > + value << offset);
> > > > +}
> > > > +
> > > > +static int da9062_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
> > > > +{
> > > > + struct da9062_gpio *gpio = gpiochip_get_data(gc);
> > > > + struct regmap *regmap = gpio->da9062->regmap;
> > > > + int gpio_dir;
> > > > +
> > > > + gpio_dir = da9062_gpio_get_pin_mode(regmap, offset);
> > > > + if (gpio_dir < 0)
> > > > + return gpio_dir;
> > > > +
> > > > + switch (gpio_dir) {
> > > > + case DA9062_PIN_ALTERNATE:
> > > > + return -ENOTSUPP;
> > > > + case DA9062_PIN_GPI:
> > > > + return 1;
> > > > + case DA9062_PIN_GPO_OD:
> > > > + /* falltrough */
> > > > + case DA9062_PIN_GPO_PP:
> > > > + return 0;
> > > > + }
> > > > +
> > > > + return -EINVAL;
> > > > +}
> > > > +
> > > > +static int da9062_gpio_direction_input(struct gpio_chip *gc,
> > > > + unsigned int offset)
> > > > +{
> > > > + struct da9062_gpio *gpio = gpiochip_get_data(gc);
> > > > + struct regmap *regmap = gpio->da9062->regmap;
> > > > + struct gpio_desc *desc = gpiochip_get_desc(gc, offset);
> > > > + unsigned int gpi_type;
> > > > + int ret;
> > > > +
> > > > + ret = da9062_gpio_set_pin_mode(regmap, offset, DA9062_PIN_GPI);
> > > > + if (ret)
> > > > + return ret;
> > > > +
> > > > + /*
> > > > + * If the gpio is active low we should set it in hw too. No worries
> > > > + * about gpio_get() because we read and return the gpio-level. So the
> > > > + * gpiolob active_low handling is still correct.
> > > > + *
> > > > + * 0 - active low, 1 - active high
> > > > + */
> > > > + gpi_type = !gpiod_is_active_low(desc);
> > > > + return regmap_update_bits(regmap, DA9062AA_GPIO_0_1 + (offset >> 1),
> > > > + DA9062AA_GPIO0_TYPE_MASK << DA9062_TYPE(offset),
> > > > + gpi_type << DA9062_TYPE(offset));
> > > > +}
> > > > +
> > > > +static int da9062_gpio_direction_output(struct gpio_chip *gc,
> > > > + unsigned int offset, int value)
> > > > +{
> > > > + /* Push-Pull / Open-Drain options are configured during set_config */
> > > > + da9062_gpio_set(gc, offset, value);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int da9062_gpio_set_config(struct gpio_chip *gc, unsigned int offset,
> > > > + unsigned long config)
> > > > +{
> > > > + struct da9062_gpio *gpio = gpiochip_get_data(gc);
> > > > + struct regmap *regmap = gpio->da9062->regmap;
> > > > + int gpio_dir;
> > > > +
> > > > + switch (pinconf_to_config_param(config)) {
> > > > + case PIN_CONFIG_BIAS_PULL_DOWN:
> > > > + /* PD only if pin is input */
> > > > + gpio_dir = da9062_gpio_get_pin_mode(regmap, offset);
> > > > + if (gpio_dir < 0)
> > > > + return -EINVAL;
> > > > + else if (gpio_dir != DA9062_PIN_GPI)
> > > > + return -ENOTSUPP;
> > > > + return regmap_update_bits(regmap, DA9062AA_CONFIG_K,
> > > > + BIT(offset), BIT(offset));
> > > > + case PIN_CONFIG_BIAS_PULL_UP:
> > > > + /* PU only if pin is output open-drain */
> > > > + gpio_dir = da9062_gpio_get_pin_mode(regmap, offset);
> > > > + if (gpio_dir < 0)
> > > > + return -EINVAL;
> > > > + else if (gpio_dir != DA9062_PIN_GPO_OD)
> > > > + return -ENOTSUPP;
> > > > + return regmap_update_bits(regmap, DA9062AA_CONFIG_K,
> > > > + BIT(offset), BIT(offset));
> > > > + case PIN_CONFIG_DRIVE_OPEN_DRAIN:
> > > > + return da9062_gpio_set_pin_mode(regmap, offset,
> > > > + DA9062_PIN_GPO_OD);
> > > > + case PIN_CONFIG_DRIVE_PUSH_PULL:
> > > > + return da9062_gpio_set_pin_mode(regmap, offset,
> > > > + DA9062_PIN_GPO_PP);
> > > > + default:
> > > > + return -ENOTSUPP;
> > > > + }
> > > > +}
> > > > +
> > > > +static int da9062_gpio_to_irq(struct gpio_chip *gc, unsigned int offset)
> > > > +{
> > > > + struct da9062_gpio *gpio = gpiochip_get_data(gc);
> > > > + struct da9062 *da9062 = gpio->da9062;
> > > > +
> > > > + return regmap_irq_get_virq(da9062->regmap_irq,
> > > > + DA9062_IRQ_GPI0 + offset);
> > > > +}
> > > > +
> > >
> > > I'm afraid this won't fly anymore. We now have support for
> > > hierarchical GPIO irqchips (take a look at
> > > Documentation/driver-api/gpio/driver.rst) and Linus is quite strict on
> > > enforcing its usage. What I did with a very simple mfd device with
> > > GPIOs (where using hierarchical irqchips was clearly overkill) was to
> > > put the gpio-controller on the same DT node as the core mfd device -
> > > that way there's no need for a hierarchy.
> >
> > Okay, I've checked the documentation and the code. If I understood it
> > right I should request each irq using platform_get_irq_byname() as you
> > did for the max77650?
> >
>
> No, regmap irq domain is fine, as long as you modify the DT bindings
> to not use a sub-node for the gpio-controller.
Ah okay.. thanks for clearing that.
Regards,
Marco
> > Regards,
> > Marco
> >
> > > Bart
> > >
> > > > +static const struct gpio_chip reference_gp = {
> > > > + .label = "da9062-gpio",
> > > > + .owner = THIS_MODULE,
> > > > + .get = da9062_gpio_get,
> > > > + .set = da9062_gpio_set,
> > > > + .get_direction = da9062_gpio_get_direction,
> > > > + .direction_input = da9062_gpio_direction_input,
> > > > + .direction_output = da9062_gpio_direction_output,
> > > > + .set_config = da9062_gpio_set_config,
> > > > + .to_irq = da9062_gpio_to_irq,
> > > > + .can_sleep = true,
> > > > + .ngpio = DA9062_GPIO_NUM,
> > > > + .base = -1,
> > > > +};
> > > > +
> > > > +static int da9062_gpio_probe(struct platform_device *pdev)
> > > > +{
> > > > + struct da9062_gpio *gpio;
> > > > +
> > > > + gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
> > > > + if (!gpio)
> > > > + return -ENOMEM;
> > > > +
> > > > + gpio->da9062 = dev_get_drvdata(pdev->dev.parent);
> > > > + if (!gpio->da9062)
> > > > + return -EINVAL;
> > > > +
> > > > + gpio->gp = reference_gp;
> > > > + gpio->gp.parent = &pdev->dev;
> > > > +
> > > > + platform_set_drvdata(pdev, gpio);
> > > > +
> > > > + return devm_gpiochip_add_data(&pdev->dev, &gpio->gp, gpio);
> > > > +}
> > > > +
> > > > +static const struct of_device_id da9062_compatible_id_table[] = {
> > > > + { .compatible = "dlg,da9062-gpio" },
> > > > + { },
> > > > +};
> > > > +MODULE_DEVICE_TABLE(of, da9062_compatible_id_table);
> > > > +
> > > > +static struct platform_driver da9062_gpio_driver = {
> > > > + .probe = da9062_gpio_probe,
> > > > + .driver = {
> > > > + .name = "da9062-gpio",
> > > > + .of_match_table = da9062_compatible_id_table,
> > > > + },
> > > > +};
> > > > +module_platform_driver(da9062_gpio_driver);
> > > > +
> > > > +MODULE_AUTHOR("Marco Felsch <kernel@xxxxxxxxxxxxxx>");
> > > > +MODULE_DESCRIPTION("DA9062 GPIO Device Driver");
> > > > +MODULE_LICENSE("GPL v2");
> > > > +MODULE_ALIAS("platform:da9062-gpio");
> > > > diff --git a/include/linux/mfd/da9062/gpio.h b/include/linux/mfd/da9062/gpio.h
> > > > new file mode 100644
> > > > index 000000000000..67627ada1ad4
> > > > --- /dev/null
> > > > +++ b/include/linux/mfd/da9062/gpio.h
> > > > @@ -0,0 +1,13 @@
> > > > +/* SPDX-License-Identifier: GPL-2.0 */
> > > > +/*
> > > > + * Copyright (C) 2019 Pengutronix, Marco Felsch <kernel@xxxxxxxxxxxxxx>
> > > > + */
> > > > +
> > > > +#ifndef __MFD_DA9062_GPIO_H__
> > > > +#define __MFD_DA9062_GPIO_H__
> > > > +
> > > > +struct gpio_desc;
> > > > +
> > > > +int da9062_gpio_get_hwgpio(struct gpio_desc *desc);
> > > > +
> > > > +#endif /* __MFD_DA9062_GPIO_H__ */
> > > > --
> > > > 2.20.1
> > > >
> > >
> >
> > --
> > Pengutronix e.K. | |
> > Industrial Linux Solutions | http://www.pengutronix.de/ |
> > Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> > Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
