[PATCH 3/4] usb: usb251xb: simplify reset helper

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Currently the reset handler was always called to deassert the reset
line because assert the line was done during probe. Now if we want to
support pm by turn of the supply we need to call this routine twice and
the i2c_lock_bus is done twice too. To simplify that we can drop the
state and just do a reset in one go. So a future pm operation don't need
to lock the i2c bus twice.

Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>
---
 drivers/usb/misc/usb251xb.c | 15 +++++++--------
 1 file changed, 7 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/misc/usb251xb.c b/drivers/usb/misc/usb251xb.c
index 05819167604d..bc031d33f433 100644
--- a/drivers/usb/misc/usb251xb.c
+++ b/drivers/usb/misc/usb251xb.c
@@ -263,20 +263,19 @@ static int usb251x_check_gpio_chip(struct usb251xb *hub)
 }
 #endif
 
-static void usb251xb_reset(struct usb251xb *hub, int state)
+static void usb251xb_reset(struct usb251xb *hub)
 {
 	if (!hub->gpio_reset)
 		return;
 
 	i2c_lock_bus(hub->i2c->adapter, I2C_LOCK_SEGMENT);
 
-	gpiod_set_value_cansleep(hub->gpio_reset, state);
+	gpiod_set_value_cansleep(hub->gpio_reset, 1);
+	usleep_range(1, 10);	/* >=1us RESET_N asserted */
+	gpiod_set_value_cansleep(hub->gpio_reset, 0);
 
 	/* wait for hub recovery/stabilization */
-	if (!state)
-		usleep_range(500, 750);	/* >=500us at power on */
-	else
-		usleep_range(1, 10);	/* >=1us at power down */
+	usleep_range(500, 750);	/* >=500us after RESET_N deasserted */
 
 	i2c_unlock_bus(hub->i2c->adapter, I2C_LOCK_SEGMENT);
 }
@@ -294,7 +293,7 @@ static int usb251xb_connect(struct usb251xb *hub)
 		i2c_wb[0] = 0x01;
 		i2c_wb[1] = USB251XB_STATUS_COMMAND_ATTACH;
 
-		usb251xb_reset(hub, 0);
+		usb251xb_reset(hub);
 
 		err = i2c_smbus_write_i2c_block_data(hub->i2c,
 				USB251XB_ADDR_STATUS_COMMAND, 2, i2c_wb);
@@ -344,7 +343,7 @@ static int usb251xb_connect(struct usb251xb *hub)
 	i2c_wb[USB251XB_ADDR_PORT_MAP_7]        = hub->port_map7;
 	i2c_wb[USB251XB_ADDR_STATUS_COMMAND] = USB251XB_STATUS_COMMAND_ATTACH;
 
-	usb251xb_reset(hub, 0);
+	usb251xb_reset(hub);
 
 	/* write registers */
 	for (i = 0; i < (USB251XB_I2C_REG_SZ / USB251XB_I2C_WRITE_SZ); i++) {
-- 
2.20.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux