[PATCH v2 1/6] dt-bindings: pci: amlogic,meson-pcie: Add G12A bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add PCIE bindings for the Amlogic G12A SoC, the support is the same
but the PHY is shared with USB3 to control the differential lines.

Thus this adds a phy phandle to control the PHY, and only requires the
MIPI clock for the Amlogic AXG SoC Family.

Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
---
 .../devicetree/bindings/pci/amlogic,meson-pcie.txt   | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
index efa2c8b9b85a..84fdc422792e 100644
--- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
@@ -9,13 +9,16 @@ Additional properties are described here:
 
 Required properties:
 - compatible:
-	should contain "amlogic,axg-pcie" to identify the core.
+	should contain :
+	- "amlogic,axg-pcie" for AXG SoC Family
+	- "amlogic,g12a-pcie" for G12A SoC Family
+	to identify the core.
 - reg:
 	should contain the configuration address space.
 - reg-names: Must be
 	- "elbi"	External local bus interface registers
 	- "cfg"		Meson specific registers
-	- "phy"		Meson PCIE PHY registers
+	- "phy"		Meson PCIE PHY registers for AXG SoC Family
 	- "config"	PCIe configuration space
 - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
 - clocks: Must contain an entry for each entry in clock-names.
@@ -23,12 +26,13 @@ Required properties:
 	- "pclk"       PCIe GEN 100M PLL clock
 	- "port"       PCIe_x(A or B) RC clock gate
 	- "general"    PCIe Phy clock
-	- "mipi"       PCIe_x(A or B) 100M ref clock gate
+	- "mipi"       PCIe_x(A or B) 100M ref clock gate for AXG SoC Family
 - resets: phandle to the reset lines.
 - reset-names: must contain "phy" "port" and "apb"
-       - "phy"         Share PHY reset
+       - "phy"         Share PHY reset for AXG SoC Family
        - "port"        Port A or B reset
        - "apb"         Share APB reset
+- phys: should contain a phandle to the shared phy for G12A SoC Family
 - device_type:
 	should be "pci". As specified in designware-pcie.txt
 
-- 
2.22.0




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux