Lad, Prabhakar <prabhakar.csengg@xxxxxxxxx> wrote on Sat [2019-Sep-14 11:33:42 +0100]:
> Hi Benoit,
>
> On Thu, Sep 12, 2019 at 1:58 PM Benoit Parrot <bparrot@xxxxxx> wrote:
> >
> > On some board it is possible that the sensor 'powerdown'
> > pin might be controlled with a gpio instead of being
> > tied to always powered.
> >
> > This patch add support to specify an optional gpio
> > which will be set at probe time and remained on.
> >
> > Signed-off-by: Benoit Parrot <bparrot@xxxxxx>
> > ---
> > drivers/media/i2c/Kconfig | 2 +-
> > drivers/media/i2c/ov2659.c | 13 +++++++++++++
> > 2 files changed, 14 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> > index 7eee1812bba3..315c1d8bdb7b 100644
> > --- a/drivers/media/i2c/Kconfig
> > +++ b/drivers/media/i2c/Kconfig
> > @@ -634,7 +634,7 @@ config VIDEO_OV2640
> > config VIDEO_OV2659
> > tristate "OmniVision OV2659 sensor support"
> > depends on VIDEO_V4L2 && I2C
> > - depends on MEDIA_CAMERA_SUPPORT
> > + depends on MEDIA_CAMERA_SUPPORT && GPIOLIB
> > select V4L2_FWNODE
> > help
> > This is a Video4Linux2 sensor driver for the OmniVision
> > diff --git a/drivers/media/i2c/ov2659.c b/drivers/media/i2c/ov2659.c
> > index efbe6dc720e2..c64f73bef336 100644
> > --- a/drivers/media/i2c/ov2659.c
> > +++ b/drivers/media/i2c/ov2659.c
> > @@ -32,6 +32,8 @@
> > #include <linux/module.h>
> > #include <linux/of.h>
> > #include <linux/of_graph.h>
> > +#include <linux/of_gpio.h>
> > +#include <linux/gpio/consumer.h>
> > #include <linux/slab.h>
> > #include <linux/uaccess.h>
> > #include <linux/videodev2.h>
> > @@ -232,6 +234,8 @@ struct ov2659 {
> > struct sensor_register *format_ctrl_regs;
> > struct ov2659_pll_ctrl pll;
> > int streaming;
> > + /* used to control the sensor powerdownN pin */
> > + struct gpio_desc *pwrdn_gpio;
> > };
> >
> > static const struct sensor_register ov2659_init_regs[] = {
> > @@ -1391,6 +1395,7 @@ static int ov2659_probe(struct i2c_client *client)
> > struct v4l2_subdev *sd;
> > struct ov2659 *ov2659;
> > struct clk *clk;
> > + struct gpio_desc *gpio;
>
> you don't need the local var here you can just assign it directly to pwrdn_gpio.
Ok.
>
> > int ret;
> >
> > if (!pdata) {
> > @@ -1414,6 +1419,14 @@ static int ov2659_probe(struct i2c_client *client)
> > ov2659->xvclk_frequency > 27000000)
> > return -EINVAL;
> >
> > + /* Optional gpio don't fail if not present */
> > + gpio = devm_gpiod_get_optional(&client->dev, "powerdown",
> > + GPIOD_OUT_HIGH);
> > + if (IS_ERR(gpio))
> > + return PTR_ERR(gpio);
> > +
> > + ov2659->pwrdn_gpio = gpio;
> > +
> apart from assigning it you don't actually use it.
>
> you will also have to read the reset gpio pin and implement
> ov2659_set_power() and
> call it in appropriate places/ s_power ?
Well I am not sure I want to go that far.
On most board I have the sensor is always powered as soon as the board gets
powered. Which is why we go through a S/W reset before starting a stream.
I didn't want to change the logic here too much.
I'll check this out a little more.
Benoit
>
> Cheers,
> --Prabhakar Lad
