This should make the driver usable with VIA/WonderMedia ARM-based Systems-on-Chip integrated Rhine III adapters. Note that these are always in MMIO mode, and don't have any known EEPROM. Signed-off-by: Alexey Charkov <alchark@xxxxxxxxx> --- .../devicetree/bindings/net/via-rhine.txt | 17 ++ arch/arm/boot/dts/vt8500.dtsi | 6 + arch/arm/boot/dts/wm8650.dtsi | 6 + arch/arm/boot/dts/wm8850.dtsi | 6 + drivers/net/ethernet/via/Kconfig | 2 +- drivers/net/ethernet/via/via-rhine.c | 307 +++++++++++++-------- 6 files changed, 229 insertions(+), 115 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/via-rhine.txt diff --git a/Documentation/devicetree/bindings/net/via-rhine.txt b/Documentation/devicetree/bindings/net/via-rhine.txt new file mode 100644 index 0000000..334eca2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-rhine.txt @@ -0,0 +1,17 @@ +* VIA Rhine 10/100 Network Controller + +Required properties: +- compatible : Should be "via,vt8500-rhine" for integrated + Rhine controllers found in VIA VT8500, WonderMedia WM8950 + and similar. These are listed as 1106:3106 rev. 0x84 on the + virtual PCI bus under vendor-provided kernels +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Examples: + +ethernet@d8004000 { + compatible = "via,vt8500-rhine"; + reg = <0xd8004000 0x100>; + interrupts = <10>; +}; diff --git a/arch/arm/boot/dts/vt8500.dtsi b/arch/arm/boot/dts/vt8500.dtsi index 51d0e91..1929ad3 100644 --- a/arch/arm/boot/dts/vt8500.dtsi +++ b/arch/arm/boot/dts/vt8500.dtsi @@ -165,5 +165,11 @@ reg = <0xd8100000 0x10000>; interrupts = <48>; }; + + ethernet@d8004000 { + compatible = "via,vt8500-rhine"; + reg = <0xd8004000 0x100>; + interrupts = <10>; + }; }; }; diff --git a/arch/arm/boot/dts/wm8650.dtsi b/arch/arm/boot/dts/wm8650.dtsi index 7525982..b1c59a7 100644 --- a/arch/arm/boot/dts/wm8650.dtsi +++ b/arch/arm/boot/dts/wm8650.dtsi @@ -218,5 +218,11 @@ reg = <0xd8100000 0x10000>; interrupts = <48>; }; + + ethernet@d8004000 { + compatible = "via,vt8500-rhine"; + reg = <0xd8004000 0x100>; + interrupts = <10>; + }; }; }; diff --git a/arch/arm/boot/dts/wm8850.dtsi b/arch/arm/boot/dts/wm8850.dtsi index d98386d..8fbccfbe 100644 --- a/arch/arm/boot/dts/wm8850.dtsi +++ b/arch/arm/boot/dts/wm8850.dtsi @@ -298,5 +298,11 @@ bus-width = <4>; sdon-inverted; }; + + ethernet@d8004000 { + compatible = "via,vt8500-rhine"; + reg = <0xd8004000 0x100>; + interrupts = <10>; + }; }; }; diff --git a/drivers/net/ethernet/via/Kconfig b/drivers/net/ethernet/via/Kconfig index 8a049a2..f66ddae 100644 --- a/drivers/net/ethernet/via/Kconfig +++ b/drivers/net/ethernet/via/Kconfig @@ -19,7 +19,7 @@ if NET_VENDOR_VIA config VIA_RHINE tristate "VIA Rhine support" - depends on PCI + depends on (PCI || USE_OF) select CRC32 select MII ---help--- diff --git a/drivers/net/ethernet/via/via-rhine.c b/drivers/net/ethernet/via/via-rhine.c index 20b83f1..4fa9201 100644 --- a/drivers/net/ethernet/via/via-rhine.c +++ b/drivers/net/ethernet/via/via-rhine.c @@ -94,6 +94,10 @@ static const int multicast_filter_limit = 32; #include <linux/ioport.h> #include <linux/interrupt.h> #include <linux/pci.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/platform_device.h> #include <linux/dma-mapping.h> #include <linux/netdevice.h> #include <linux/etherdevice.h> @@ -279,6 +283,15 @@ static DEFINE_PCI_DEVICE_TABLE(rhine_pci_tbl) = { }; MODULE_DEVICE_TABLE(pci, rhine_pci_tbl); +/* OpenFirmware identifiers for platform-bus devices + * The .data field is currently only used to store chip revision + * (for quirks etc.) + */ +static struct of_device_id rhine_of_tbl[] = { + { .compatible = "via,vt8500-rhine", .data = (void *)0x84 }, + { } /* terminate list */ +}; +MODULE_DEVICE_TABLE(of, rhine_of_tbl); /* Offsets to the device registers. */ enum register_offsets { @@ -847,7 +860,8 @@ static void rhine_hw_init(struct net_device *dev, long pioaddr) msleep(5); /* Reload EEPROM controlled bytes cleared by soft reset */ - rhine_reload_eeprom(pioaddr, dev); + if (dev_is_pci(dev->dev.parent)) + rhine_reload_eeprom(pioaddr, dev); } static const struct net_device_ops rhine_netdev_ops = { @@ -868,125 +882,55 @@ static const struct net_device_ops rhine_netdev_ops = { #endif }; -static int rhine_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) +static int rhine_init_one_common(struct device *hwdev, int revision, + long pioaddr, void __iomem *ioaddr, int irq) { struct net_device *dev; struct rhine_private *rp; - struct device *hwdev = &pdev->dev; - int revision = pdev->revision; - int i, rc; - u32 quirks; - long pioaddr; - long memaddr; - void __iomem *ioaddr; - int io_size, phy_id; + int i, rc, phy_id; const char *name; -#ifdef USE_MMIO - int bar = 1; -#else - int bar = 0; -#endif - -/* when built into the kernel, we only print version if device is found */ -#ifndef MODULE - pr_info_once("%s\n", version); -#endif - - io_size = 256; - phy_id = 0; - quirks = 0; - name = "Rhine"; - if (revision < VTunknown0) { - quirks = rqRhineI; - io_size = 128; - } else if (revision >= VT6102) { - quirks = rqWOL | rqForceReset; - if (revision < VT6105) { - name = "Rhine II"; - quirks |= rqStatusWBRace; /* Rhine-II exclusive */ - } else { - phy_id = 1; /* Integrated PHY, phy_id fixed to 1 */ - if (revision >= VT6105_B0) - quirks |= rq6patterns; - if (revision < VT6105M) - name = "Rhine III"; - else - name = "Rhine III (Management Adapter)"; - } - } - - rc = pci_enable_device(pdev); - if (rc) - goto err_out; /* this should always be supported */ rc = dma_set_mask(hwdev, DMA_BIT_MASK(32)); if (rc) { dev_err(hwdev, "32-bit DMA addresses not supported by the card!?\n"); - goto err_out_pci_disable; - } - - /* sanity check */ - if ((pci_resource_len(pdev, 0) < io_size) || - (pci_resource_len(pdev, 1) < io_size)) { - rc = -EIO; - dev_err(hwdev, "Insufficient PCI resources, aborting\n"); - goto err_out_pci_disable; + goto err_out; } - pioaddr = pci_resource_start(pdev, 0); - memaddr = pci_resource_start(pdev, 1); - - pci_set_master(pdev); - dev = alloc_etherdev(sizeof(struct rhine_private)); if (!dev) { rc = -ENOMEM; - goto err_out_pci_disable; + goto err_out; } SET_NETDEV_DEV(dev, hwdev); rp = netdev_priv(dev); rp->dev = dev; rp->revision = revision; - rp->quirks = quirks; rp->pioaddr = pioaddr; + rp->base = ioaddr; + rp->irq = irq; rp->msg_enable = netif_msg_init(debug, RHINE_MSG_DEFAULT); - rc = pci_request_regions(pdev, DRV_NAME); - if (rc) - goto err_out_free_netdev; - - ioaddr = pci_iomap(pdev, bar, io_size); - if (!ioaddr) { - rc = -EIO; - dev_err(hwdev, - "ioremap failed for device %s, region 0x%X @ 0x%lX\n", - dev_name(hwdev), io_size, memaddr); - goto err_out_free_res; - } - -#ifdef USE_MMIO - enable_mmio(pioaddr, quirks); - - /* Check that selected MMIO registers match the PIO ones */ - i = 0; - while (mmio_verify_registers[i]) { - int reg = mmio_verify_registers[i++]; - unsigned char a = inb(pioaddr+reg); - unsigned char b = readb(ioaddr+reg); - if (a != b) { - rc = -EIO; - dev_err(hwdev, - "MMIO do not match PIO [%02x] (%02x != %02x)\n", - reg, a, b); - goto err_out_unmap; + phy_id = 0; + name = "Rhine"; + if (revision < VTunknown0) { + rp->quirks = rqRhineI; + } else if (revision >= VT6102) { + rp->quirks = rqWOL | rqForceReset; + if (revision < VT6105) { + name = "Rhine II"; + rp->quirks |= rqStatusWBRace; /* Rhine-II exclusive */ + } else { + phy_id = 1; /* Integrated PHY, phy_id fixed to 1 */ + if (revision >= VT6105_B0) + rp->quirks |= rq6patterns; + if (revision < VT6105M) + name = "Rhine III"; + else + name = "Rhine III (Management Adapter)"; } } -#endif /* USE_MMIO */ - - rp->base = ioaddr; - rp->irq = pdev->irq; u64_stats_init(&rp->tx_stats.syncp); u64_stats_init(&rp->rx_stats.syncp); @@ -1039,16 +983,10 @@ static int rhine_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) /* dev->name not defined before register_netdev()! */ rc = register_netdev(dev); if (rc) - goto err_out_unmap; + goto err_out_free_netdev; netdev_info(dev, "VIA %s at 0x%lx, %pM, IRQ %d\n", - name, -#ifdef USE_MMIO - memaddr, -#else - (long)ioaddr, -#endif - dev->dev_addr, rp->irq); + name, (long)ioaddr, dev->dev_addr, rp->irq); dev_set_drvdata(hwdev, dev); @@ -1079,18 +1017,126 @@ static int rhine_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) return 0; +err_out_free_netdev: + free_netdev(dev); +err_out: + return rc; +} + +static int rhine_init_one_pci(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct device *hwdev = &pdev->dev; + int i, rc; + long pioaddr, memaddr; + void __iomem *ioaddr; + int io_size = pdev->revision < VTunknown0 ? 128 : 256; + u32 quirks = pdev->revision < VTunknown0 ? rqRhineI : 0; +#ifdef USE_MMIO + int bar = 1; +#else + int bar = 0; +#endif + +/* when built into the kernel, we only print version if device is found */ +#ifndef MODULE + pr_info_once("%s\n", version); +#endif + + rc = pci_enable_device(pdev); + if (rc) + goto err_out; + + /* sanity check */ + if ((pci_resource_len(pdev, 0) < io_size) || + (pci_resource_len(pdev, 1) < io_size)) { + rc = -EIO; + dev_err(hwdev, "Insufficient PCI resources, aborting\n"); + goto err_out_pci_disable; + } + + pioaddr = pci_resource_start(pdev, 0); + memaddr = pci_resource_start(pdev, 1); + + pci_set_master(pdev); + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) + goto err_out_pci_disable; + + ioaddr = pci_iomap(pdev, bar, io_size); + if (!ioaddr) { + rc = -EIO; + dev_err(hwdev, + "ioremap failed for device %s, region 0x%X @ 0x%lX\n", + dev_name(hwdev), io_size, memaddr); + goto err_out_free_res; + } + +#ifdef USE_MMIO + enable_mmio(pioaddr, quirks); + + /* Check that selected MMIO registers match the PIO ones */ + i = 0; + while (mmio_verify_registers[i]) { + int reg = mmio_verify_registers[i++]; + unsigned char a = inb(pioaddr+reg); + unsigned char b = readb(ioaddr+reg); + + if (a != b) { + rc = -EIO; + dev_err(hwdev, + "MMIO do not match PIO [%02x] (%02x != %02x)\n", + reg, a, b); + goto err_out_unmap; + } + } +#endif /* USE_MMIO */ + + rc = rhine_init_one_common(&pdev->dev, pdev->revision, + pioaddr, ioaddr, pdev->irq); + if (!rc) + return 0; + err_out_unmap: pci_iounmap(pdev, ioaddr); err_out_free_res: pci_release_regions(pdev); -err_out_free_netdev: - free_netdev(dev); err_out_pci_disable: pci_disable_device(pdev); err_out: return rc; } +static int rhine_init_one_platform(struct platform_device *pdev) +{ + const struct of_device_id *match; + u32 revision; + int irq; + struct resource *res; + void __iomem *ioaddr; + + match = of_match_device(rhine_of_tbl, &pdev->dev); + if (!match) + return -EINVAL; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + ioaddr = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(ioaddr)) + return PTR_ERR(ioaddr); + + irq = irq_of_parse_and_map(pdev->dev.of_node, 0); + if (!irq) + return -EINVAL; + + revision = (u32)match->data; + if (!revision) + return -EINVAL; + + return rhine_init_one_common(&pdev->dev, revision, + (long)ioaddr, ioaddr, irq); +} + static int alloc_ring(struct net_device* dev) { struct rhine_private *rp = netdev_priv(dev); @@ -2297,7 +2343,7 @@ static int rhine_close(struct net_device *dev) } -static void rhine_remove_one(struct pci_dev *pdev) +static void rhine_remove_one_pci(struct pci_dev *pdev) { struct net_device *dev = pci_get_drvdata(pdev); struct rhine_private *rp = netdev_priv(dev); @@ -2311,7 +2357,21 @@ static void rhine_remove_one(struct pci_dev *pdev) pci_disable_device(pdev); } -static void rhine_shutdown (struct pci_dev *pdev) +static int rhine_remove_one_platform(struct platform_device *pdev) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct rhine_private *rp = netdev_priv(dev); + + unregister_netdev(dev); + + iounmap(rp->base); + + free_netdev(dev); + + return 0; +} + +static void rhine_shutdown_pci(struct pci_dev *pdev) { struct net_device *dev = pci_get_drvdata(pdev); struct rhine_private *rp = netdev_priv(dev); @@ -2378,7 +2438,7 @@ static int rhine_suspend(struct device *device) netif_device_detach(dev); if (dev_is_pci(device)) - rhine_shutdown(to_pci_dev(device)); + rhine_shutdown_pci(to_pci_dev(device)); return 0; } @@ -2418,15 +2478,26 @@ static SIMPLE_DEV_PM_OPS(rhine_pm_ops, rhine_suspend, rhine_resume); #endif /* !CONFIG_PM_SLEEP */ -static struct pci_driver rhine_driver = { +static struct pci_driver rhine_driver_pci = { .name = DRV_NAME, .id_table = rhine_pci_tbl, - .probe = rhine_init_one, - .remove = rhine_remove_one, - .shutdown = rhine_shutdown, + .probe = rhine_init_one_pci, + .remove = rhine_remove_one_pci, + .shutdown = rhine_shutdown_pci, .driver.pm = RHINE_PM_OPS, }; +static struct platform_driver rhine_driver_platform = { + .probe = rhine_init_one_platform, + .remove = rhine_remove_one_platform, + .driver = { + .name = DRV_NAME, + .owner = THIS_MODULE, + .of_match_table = rhine_of_tbl, + .pm = RHINE_PM_OPS, + } +}; + static struct dmi_system_id rhine_dmi_table[] __initdata = { { .ident = "EPIA-M", @@ -2447,6 +2518,8 @@ static struct dmi_system_id rhine_dmi_table[] __initdata = { static int __init rhine_init(void) { + int ret_pci, ret_platform; + /* when a module, this is printed whether or not devices are found in probe */ #ifdef MODULE pr_info("%s\n", version); @@ -2459,13 +2532,19 @@ static int __init rhine_init(void) else if (avoid_D3) pr_info("avoid_D3 set\n"); - return pci_register_driver(&rhine_driver); + ret_pci = pci_register_driver(&rhine_driver_pci); + ret_platform = platform_driver_register(&rhine_driver_platform); + if ((ret_pci < 0) && (ret_platform < 0)) + return ret_pci; + + return 0; } static void __exit rhine_cleanup(void) { - pci_unregister_driver(&rhine_driver); + platform_driver_unregister(&rhine_driver_platform); + pci_unregister_driver(&rhine_driver_pci); } -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html