On Mon, 2019-08-12 at 14:21 +0000, Philippe Schenker wrote:
> From: Igor Opaniuk <igor.opaniuk@xxxxxxxxxxx>
>
> Provide proper configuration for VGEN3, to make sure it's is always
> powered
> which allows that rail to be automatically switched to 1.8 volts
> for proper UHS-I operation. By default it's disabled.
>
> With UHS-I enabled:
> [ 104.153898] mmc1: new ultra high speed SDR104 SDHC card at address
> 59b4
> [ 104.166202] mmcblk1: mmc1:59b4 USD00 15.0 GiB
> [ 104.173923] mmcblk1: p1
>
> root@colibri-imx6:~# hdparm -t /dev/mmcblk1
> /dev/mmcblk1:
> Timing buffered disk reads: 226 MB in 3.01 seconds = 75.01 MB/sec
>
> Signed-off-by: Igor Opaniuk <igor.opaniuk@xxxxxxxxxxx>
> Signed-off-by: Philippe Schenker <philippe.schenker@xxxxxxxxxxx>
Please ignore this patch. There was a misunderstanding and this one
shouldn't go into mainline. Sorry for that!
>
> ---
>
> Changes in v4:
> - New patch as of the recommendation from Marcel on ML
>
> Changes in v3: None
> Changes in v2: None
>
> arch/arm/boot/dts/imx6qdl-colibri.dtsi | 43 +++++++++++++++++++++++
> ---
> 1 file changed, 39 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
> b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
> index 9a63debab0b5..0241613b5e2b 100644
> --- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
> @@ -226,7 +226,12 @@
> regulator-always-on;
> };
>
> - /* vgen3: unused */
> + vgen3_reg: vgen3 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
>
> vgen4_reg: vgen4 {
> regulator-min-microvolt = <1800000>;
> @@ -394,13 +399,21 @@
>
> /* Colibri MMC */
> &usdhc1 {
> - pinctrl-names = "default";
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
> + vqmmc-supply = <&vgen3_reg>;
> + sd-uhs-sdr12;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + label = "MMC1";
> cd-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* MMCD */
> disable-wp;
> - vqmmc-supply = <®_module_3v3>;
> + enable-sdio-wakeup;
> + keep-power-in-suspend;
> bus-width = <4>;
> - no-1-8-v;
> status = "disabled";
> };
>
> @@ -706,6 +719,28 @@
> >;
> };
>
> + pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170b1
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100b1
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f1
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f1
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
> + >;
> + };
> +
> pinctrl_usdhc3: usdhc3grp {
> fsl,pins = <
> MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> --
> 2.22.0
>
