Re: [RFC,v2 3/6] media: dt-bindings: add DS90UB954-Q1 video deserializer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jul 23, 2019 at 10:37:20PM +0200, Luca Ceresoli wrote:
> Describe the Texas Instruments DS90UB954-Q1, a 2-input video deserializer
> with I2C Address Translator and remote GPIOs.
> 
> Signed-off-by: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
> 
> ---
> 
> Changes RFCv1 -> RFCv2:
> 
>  - add explicit aliases for the FPD-link RX ports (optional)
>  - add proper remote GPIO description
> ---
>  .../bindings/media/i2c/ti,ds90ub954-q1.txt    | 194 ++++++++++++++++++
>  1 file changed, 194 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.txt
> 
> diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.txt b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.txt
> new file mode 100644
> index 000000000000..73ce21ecc3b6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.txt
> @@ -0,0 +1,194 @@
> +Texas Instruments DS90UB954-Q1 dual video deserializer
> +======================================================
> +
> +The TI DS90UB954-Q1 is a MIPI CSI-2 video deserializer that forwards video
> +streams from up to two FPD-Link 3 connections to a MIPI CSI-2 output. It
> +also allows access to remote I2C and GPIO.
> +
> +Required properties:
> +
> + - compatible: must be "ti,ds90ub954-q1"
> +
> + - reg: main I2C slave address; optionally aliases for RX port registers
> +   and remote serializers. The main address is mandatory and must be the
> +   first, others are optional and fall back to defaults if not
> +   specified. See "reg-names".
> +
> + - reset-gpios: chip reset GPIO, active low (connected to PDB pin of the chip)
> + - i2c-alias-pool: list of I2C addresses that are known to be available on the
> +                   "local" (SoC-to-deser) I2C bus; they will be picked at
> +		   runtime and used as aliases to reach remove I2C chips

s/remove/remote/

Needs a vendor prefix.

> + - gpio-controller
> + - #gpio-cells: must be 3: FPD-Link 3 RX port number, remote gpio number, flags

We're pretty standardized on 2 cells for GPIO. Perhaps combine the port 
and gpio number to 1 cell.

> +
> +Optional properties:
> +
> + - reg-names: names of I2C address used to communicate with the chip, must
> +              match the "reg" values; mandatory if there are 2 or more
> +              addresses
> +    - "main": the main I2C address, used to access shared registers
> +    - "rxport0", "rxport1": I2C alias to access FPD-link RX port specific
> +      registers; must not be used by other slaves on the same bus
> +    - "ser0", "ser1": I2C alias to access the remote serializer connected
> +      on each FPD-link RX port; must not be used by other slaves on the
> +      same bus
> + - interrupts: interrupt pin from the chip
> +
> +Required subnodes:
> +
> + - ports: A ports node with one port child node per device input and output
> +          port, in accordance with the video interface bindings defined in
> +          Documentation/devicetree/bindings/media/video-interfaces.txt. The
> +          port nodes are numbered as follows:
> +
> +          Port Description
> +          ------------------------------------
> +          0    Input from FPD-Link 3 RX port 0
> +          1    Input from FPD-Link 3 RX port 1
> +          2    CSI-2 output
> +
> +          Each port must have a "remote-chip" subnode that defines the remote
> +	  chip (serializer) with at least a "compatible" property

We don't allow other nodes within graph nodes. I'm not really clear what 
you are trying to do here.

> +
> + - i2c-atr: contains one child per RX port, each describes the I2C bus on
> +            the remote side
> +
> +	    Required properties:
> +	    - #address-cells = <1>;
> +	    - #size-cells = <0>;
> +
> +	    Subnodes: one per each FPD-link RX port, each having:
> +
> +	    Required properties for "i2c-atr" child bus nodes:
> +	    - reg: The number of the port where the remove chip is connected

s/remove/remote/

> +	    - #address-cells = <1>;
> +	    - #size-cells = <0>;
> +
> +	    Optional properties for "i2c-atr" child bus nodes:
> +	    - Other properties specific to the remote hardware

Such as?

> +	    - Child nodes conforming to i2c bus binding
> +
> +
> +Device node example
> +-------------------
> +
> +&i2c0 {
> +	deser: deser@3d {
> +		compatible = "ti,ds90ub954-q1";
> +		reg-names = "main", "rxport0", "rxport1", "ser0", "ser1";
> +		reg       = <0x3d>,  <0x40>,    <0x41>,   <0x44>, <0x45>;
> +		clocks = <&clk_25M>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <3 1 IRQ_TYPE_LEVEL_HIGH>;
> +		reset-gpios = <&gpio_ctl 4 GPIO_ACTIVE_LOW>;
> +
> +		i2c-alias-pool = /bits/ 16 <0x4a 0x4b 0x4c 0x4d 0x4e 0x4f>;
> +
> +		gpio-controller;
> +		#gpio-cells = <3>; /* rxport, remote gpio num, flags */
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				ds90ub954_fpd3_in0: endpoint {
> +					remote-endpoint = <&sensor_0_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				ds90ub954_fpd3_in1: endpoint {
> +					remote-endpoint = <&sensor_1_out>;
> +				};
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +				ds90ub954_mipi_out0: endpoint {
> +					data-lanes = <1 2 3 4>;
> +					/* Actually a REFCLK multiplier */
> +					data-rate = <1600000000>;
> +					remote-endpoint = <&csirx_0_in>;
> +				};
> +			};
> +		};
> +
> +		i2c-atr {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			remote_i2c0: i2c@0 {
> +				reg = <0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;

Presumably, there are child I2C devices here. Please show that in the 
example.

> +			};
> +
> +			remote_i2c1: i2c@1 {
> +				reg = <1>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +			};
> +		};
> +	};
> +};
> +
> +&ds90ub954_fpd3_in0 {
> +	remote-chip {
> +		compatible = "ti,ds90ub953-q1";
> +		gpio-functions = <DS90_GPIO_FUNC_OUTPUT_REMOTE

Not documented.

> +				  DS90_GPIO_FUNC_UNUSED
> +				  DS90_GPIO_FUNC_UNUSED
> +				  DS90_GPIO_FUNC_UNUSED>;
> +	};
> +};
> +
> +&ds90ub954_fpd3_in1 {
> +	remote-chip {
> +		compatible = "ti,ds90ub953-q1";
> +		gpio-functions = <DS90_GPIO_FUNC_OUTPUT_REMOTE
> +				  DS90_GPIO_FUNC_UNUSED
> +				  DS90_GPIO_FUNC_UNUSED
> +				  DS90_GPIO_FUNC_UNUSED>;
> +	};
> +};
> +
> +&remote_i2c0 {
> +	sensor_0@3c {
> +		compatible = "sony,imx274";
> +		reg = <0x3c>;
> +
> +		reset-gpios = <&deser 0 0 GPIO_ACTIVE_LOW>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port@0 {
> +			reg = <0>;
> +			sensor_0_out: endpoint {
> +				remote-endpoint = <&ds90ub954_fpd3_in0>;
> +			};
> +		};
> +	};
> +};
> +
> +&remote_i2c1 {
> +	sensor_0@3c {
> +		compatible = "sony,imx274";
> +		reg = <0x3c>;
> +
> +		reset-gpios = <&deser 1 0 GPIO_ACTIVE_LOW>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port@0 {
> +			reg = <0>;
> +			sensor_1_out: endpoint {
> +				remote-endpoint = <&ds90ub954_fpd3_in1>;
> +			};
> +		};
> +	};
> +};
> -- 
> 2.17.1
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux