Down-speed auto-negotiation may not always be enabled, in which case the
PHY won't down-shift to 100 or 10 during auto-negotiation.
This change enables downshift and configures the number of retries to
default 4 (which is also in the datasheet
The downshift control mechanism can also be controlled via the phy-tunable
interface (ETHTOOL_PHY_DOWNSHIFT control).
The change has been adapted from the Aquantia PHY driver.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@xxxxxxxxxx>
---
drivers/net/phy/adin.c | 86 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 86 insertions(+)
diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
index 131a72567f25..e4afa8c2bec7 100644
--- a/drivers/net/phy/adin.c
+++ b/drivers/net/phy/adin.c
@@ -29,6 +29,17 @@
#define ADIN1300_NRG_PD_TX_EN BIT(2)
#define ADIN1300_NRG_PD_STATUS BIT(1)
+#define ADIN1300_PHY_CTRL2 0x0016
+#define ADIN1300_DOWNSPEED_AN_100_EN BIT(11)
+#define ADIN1300_DOWNSPEED_AN_10_EN BIT(10)
+#define ADIN1300_GROUP_MDIO_EN BIT(6)
+#define ADIN1300_DOWNSPEEDS_EN \
+ (ADIN1300_DOWNSPEED_AN_100_EN | ADIN1300_DOWNSPEED_AN_10_EN)
+
+#define ADIN1300_PHY_CTRL3 0x0017
+#define ADIN1300_LINKING_EN BIT(13)
+#define ADIN1300_DOWNSPEED_RETRIES_MSK GENMASK(12, 10)
+
#define ADIN1300_INT_MASK_REG 0x0018
#define ADIN1300_INT_MDIO_SYNC_EN BIT(9)
#define ADIN1300_INT_ANEG_STAT_CHNG_EN BIT(8)
@@ -257,6 +268,73 @@ static int adin_config_rmii_mode(struct phy_device *phydev)
ADIN1300_GE_RMII_CFG_REG, reg);
}
+static int adin_get_downshift(struct phy_device *phydev, u8 *data)
+{
+ int val, cnt, enable;
+
+ val = phy_read(phydev, ADIN1300_PHY_CTRL2);
+ if (val < 0)
+ return val;
+
+ cnt = phy_read(phydev, ADIN1300_PHY_CTRL3);
+ if (cnt < 0)
+ return cnt;
+
+ enable = FIELD_GET(ADIN1300_DOWNSPEEDS_EN, val);
+ cnt = FIELD_GET(ADIN1300_DOWNSPEED_RETRIES_MSK, cnt);
+
+ *data = enable & cnt ? cnt : DOWNSHIFT_DEV_DISABLE;
+
+ return 0;
+}
+
+static int adin_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+ u16 val;
+ int rc;
+
+ if (cnt == DOWNSHIFT_DEV_DISABLE)
+ return phy_clear_bits(phydev, ADIN1300_PHY_CTRL2,
+ ADIN1300_DOWNSPEEDS_EN);
+
+ if (cnt > 8)
+ return -E2BIG;
+
+ val = FIELD_PREP(ADIN1300_DOWNSPEED_RETRIES_MSK, cnt);
+ val |= ADIN1300_LINKING_EN;
+
+ rc = phy_modify(phydev, ADIN1300_PHY_CTRL3,
+ ADIN1300_LINKING_EN | ADIN1300_DOWNSPEED_RETRIES_MSK,
+ val);
+ if (rc < 0)
+ return rc;
+
+ return phy_set_bits(phydev, ADIN1300_PHY_CTRL2,
+ ADIN1300_DOWNSPEEDS_EN);
+}
+
+static int adin_get_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, void *data)
+{
+ switch (tuna->id) {
+ case ETHTOOL_PHY_DOWNSHIFT:
+ return adin_get_downshift(phydev, data);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static int adin_set_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, const void *data)
+{
+ switch (tuna->id) {
+ case ETHTOOL_PHY_DOWNSHIFT:
+ return adin_set_downshift(phydev, *(const u8 *)data);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
static int adin_config_init_edpd(struct phy_device *phydev)
{
struct adin_priv *priv = phydev->priv;
@@ -287,6 +365,10 @@ static int adin_config_init(struct phy_device *phydev)
if (rc < 0)
return rc;
+ rc = adin_set_downshift(phydev, 4);
+ if (rc < 0)
+ return rc;
+
rc = adin_config_init_edpd(phydev);
if (rc < 0)
return rc;
@@ -532,6 +614,8 @@ static struct phy_driver adin_driver[] = {
.probe = adin_probe,
.config_aneg = adin_config_aneg,
.read_status = adin_read_status,
+ .get_tunable = adin_get_tunable,
+ .set_tunable = adin_set_tunable,
.ack_interrupt = adin_phy_ack_intr,
.config_intr = adin_phy_config_intr,
.resume = genphy_resume,
@@ -546,6 +630,8 @@ static struct phy_driver adin_driver[] = {
.probe = adin_probe,
.config_aneg = adin_config_aneg,
.read_status = adin_read_status,
+ .get_tunable = adin_get_tunable,
+ .set_tunable = adin_set_tunable,
.ack_interrupt = adin_phy_ack_intr,
.config_intr = adin_phy_config_intr,
.resume = genphy_resume,
--
2.20.1
