Re: [v4 2/6] media: platform: dwc: Add MIPI CSI-2 controller driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Aug 9, 2019 at 5:38 PM Sakari Ailus <sakari.ailus@xxxxxx> wrote:
> On Tue, Jun 11, 2019 at 09:20:51PM +0200, Luis Oliveira wrote:
> > Add the Synopsys MIPI CSI-2 controller driver. This
> > controller driver is divided in platform functions and core functions.
> > This way it serves as platform for future DesignWare drivers.

> > +const struct mipi_dt csi_dt[] = {
>
> Make this static or use a common prefix that somehow resembles the name
> name of the driver.
>
> > +     {
> > +             .hex = CSI_2_YUV420_8,
> > +             .name = "YUV420_8bits",
> > +     }, {
> > +             .hex = CSI_2_YUV420_10,
> > +             .name = "YUV420_10bits",
> > +     }, {
> > +             .hex = CSI_2_YUV420_8_LEG,
> > +             .name = "YUV420_8bits_LEGACY",
> > +     }, {
> > +             .hex = CSI_2_YUV420_8_SHIFT,
> > +             .name = "YUV420_8bits_SHIFT",
> > +     }, {
> > +             .hex = CSI_2_YUV420_10_SHIFT,
> > +             .name = "YUV420_10bits_SHIFT",
> > +     }, {
> > +             .hex = CSI_2_YUV422_8,
> > +             .name = "YUV442_8bits",
> > +     }, {
> > +             .hex = CSI_2_YUV422_10,
> > +             .name = "YUV442_10bits",
> > +     }, {
> > +             .hex = CSI_2_RGB444,
> > +             .name = "RGB444",
> > +     }, {
> > +             .hex = CSI_2_RGB555,
> > +             .name = "RGB555",
> > +     }, {
> > +             .hex = CSI_2_RGB565,
> > +             .name = "RGB565",
> > +     }, {
> > +             .hex = CSI_2_RGB666,
> > +             .name = "RGB666",
> > +     }, {
> > +             .hex = CSI_2_RGB888,
> > +             .name = "RGB888",
> > +     }, {
> > +             .hex = CSI_2_RAW6,
> > +             .name = "RAW6",
> > +     }, {
> > +             .hex = CSI_2_RAW7,
> > +             .name = "RAW7",
> > +     }, {
> > +             .hex = CSI_2_RAW8,
> > +             .name = "RAW8",
> > +     }, {
> > +             .hex = CSI_2_RAW10,
> > +             .name = "RAW10",
> > +     }, {
> > +             .hex = CSI_2_RAW12,
> > +             .name = "RAW12",
> > +     }, {
> > +             .hex = CSI_2_RAW14,
> > +             .name = "RAW14",
> > +     }, {
> > +             .hex = CSI_2_RAW16,
> > +             .name = "RAW16",
> > +     },
> > +};

One may utilize __stringify() macro and do somelike

#define CSI_FMT_DESC(fmt) \
 { .hex = CSI_2_##fmt, .name = __stringify(fmt), }

And do

 CSI_FMT_DESC(RAW16),

etc.

> > +             return cfg ? v4l2_subdev_get_try_format(&dev->sd,
> > +                                                     cfg,
> > +                                                     0) : NULL;

This indentation looks ugly.
I would rather put this on one line.

> > +     dev_dbg(dev->dev,
> > +             "%s got v4l2_mbus_pixelcode. 0x%x\n", __func__,
> > +             dev->format.code);
> > +     dev_dbg(dev->dev,
> > +             "%s got width. 0x%x\n", __func__,
> > +             dev->format.width);
> > +     dev_dbg(dev->dev,
> > +             "%s got height. 0x%x\n", __func__,
> > +             dev->format.height);

__func__ is usually redundant (if Dynamic Debug in use it can be
switched at run-time).

> I'd just omit these debug prints in a driver. But adding them to the
> framework might make sense. We don't have a lot of debug prints dealing
> with user parameters in there. OTOH the common test programs largely do the
> same already.

I would rather see tracepoints instead of debug prints if we are
talking about generic solution for entire framework.

>
> > +     return &dev->format;
> > +}

> > +     struct mipi_fmt *dev_fmt;

This is simple bad name. We have dev_fmt() macro. I would rather avoid
potential collisions.

> > +     struct v4l2_mbus_framefmt *mf;
> > +
> > +     mf = dw_mipi_csi_get_format(dev, cfg, fmt->which);
> > +     if (!mf)
> > +             return -EINVAL;

Can't you rather return an error pointer in this and similar cases?

> > +     dev_vdbg(dev->dev, "%s: on=%d\n", __func__, on);

This is noise. If you would like to debug Function Tracer is a good start.

> > +     of_id = of_match_node(dw_mipi_csi_of_match, dev->of_node);
> > +     if (!of_id)
> > +             return -EINVAL;

Is it possible to have this asserted?


> > +     res = platform_get_resource(pdev, IORESOURCE_MEM, 0);

> > +     if (!res)
> > +             return -ENXIO;

Redundant. Below does the check for you.

> > +
> > +     csi->base_address = devm_ioremap_resource(dev, res);
> > +     if (IS_ERR(csi->base_address)) {

> > +             dev_err(dev, "Base address not set.\n");

Redundant. Above does print an error message for you.

> > +             return PTR_ERR(csi->base_address);
> > +     }

Moreover, use devm_platform_ioremap_resource() instead of both.

> > +     csi->ctrl_irq_number = platform_get_irq(pdev, 0);
> > +     if (csi->ctrl_irq_number < 0) {

> > +             dev_err(dev, "irq number %d not set.\n", csi->ctrl_irq_number);

Redundant since this cycle (v5.4).

> > +             ret = csi->ctrl_irq_number;

Better to do the opposite

ret = platform_get_irq();
if (ret)
 goto end;
... = ret;

> > +             goto end;
> > +     }

> > +     ret = devm_request_irq(dev, csi->ctrl_irq_number,
> > +                            dw_mipi_csi_irq1, IRQF_SHARED,
> > +                            dev_name(dev), csi);
> > +     if (ret) {
> > +             dev_err(dev, "irq csi %s failed\n", of_id->name);
> > +
> > +             goto end;
> > +     }

devm_*irq() might be a bad idea. Is it race free in your driver?

> > +static const struct of_device_id dw_mipi_csi_of_match[] = {
> > +     { .compatible = "snps,dw-csi" },

> > +     {},

Better without comma. Terminator may terminate even at compile time.

> > +};

> > +static ssize_t core_version_show(struct device *dev,
> > +                              struct device_attribute *attr,
> > +                              char *buf)
> > +{
> > +     struct platform_device *pdev = to_platform_device(dev);
> > +     struct v4l2_subdev *sd = platform_get_drvdata(pdev);
> > +     struct dw_csi *csi_dev = sd_to_mipi_csi_dev(sd);

> > +
> > +     char buffer[10];
> > +
> > +     snprintf(buffer, 10, "v.%d.%d*\n", csi_dev->hw_version_major,
> > +              csi_dev->hw_version_minor);
> > +
> > +     return strlcpy(buf, buffer, PAGE_SIZE);

Oh, can't you simple without any temprorary useless buffers?
 sprintf(buf, ...)?
(Yes, note _absence_ of *n* there)

> > +}

> > +static ssize_t n_lanes_store(struct device *dev, struct device_attribute *attr,
> > +                          const char *buf, size_t count)
> > +{
> > +     int ret;
> > +     unsigned long lanes;

> > +

More blank lines! We need them!

> > +     struct platform_device *pdev = to_platform_device(dev);
> > +     struct v4l2_subdev *sd = platform_get_drvdata(pdev);
> > +     struct dw_csi *csi_dev = sd_to_mipi_csi_dev(sd);
> > +
> > +     ret = kstrtoul(buf, 10, &lanes);
> > +     if (ret < 0)
> > +             return ret;

Can it return positive number?

> > +     dev_info(dev, "Lanes %lu\n", lanes);

Noise.
The user gets it, why to spam kernel log???

> > +     csi_dev->hw.num_lanes = lanes;
> > +
> > +     return count;
> > +}

I told once, can repeat again. Synopsys perhaps needs better reviews
inside company. Each time I see the code, it repeats same mistakes
over and over. Have you, guys, do something about it?

-- 
With Best Regards,
Andy Shevchenko



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux