On Tue, Jun 25, 2019 at 03:34:07PM +0300, Andra Danciu wrote:
> From: Richard Hu <richard.hu@xxxxxxxxxxxxxx>
>
> The current level of support yields a working console and is able to boot
> userspace from an initial ramdisk copied via u-boot in RAM.
>
> Additional subsystems that are active :
> - Ethernet
> - USB
>
> Cc: Daniel Baluta <daniel.baluta@xxxxxxx>
> Signed-off-by: Richard Hu <richard.hu@xxxxxxxxxxxxxx>
> Signed-off-by: Andra Danciu <andradanciu1997@xxxxxxxxx>
> ---
> Changes since v1:
> - renamed wandboard-pi-8m.dts to pico-pi-8m.dts
> - removed pinctrl_csi1, pinctrl_wifi_ctrl
> - used generic name for pmic
> - removed gpo node
> - delete regulator-virtuals node
> - remove always-on property from buck1-8 and ldo3-7
> - remove pmic-buck-uses-i2c-dvs property for buck1-4
>
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> arch/arm64/boot/dts/freescale/pico-pi-8m.dts | 458 +++++++++++++++++++++++++++
> 2 files changed, 459 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/pico-pi-8m.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index c043aca66572..538422903e8a 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -26,3 +26,4 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
> +dtb-$(CONFIG_ARCH_MXC) += pico-pi-8m.dtb
> diff --git a/arch/arm64/boot/dts/freescale/pico-pi-8m.dts b/arch/arm64/boot/dts/freescale/pico-pi-8m.dts
> new file mode 100644
> index 000000000000..23422c8fc43f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/pico-pi-8m.dts
> @@ -0,0 +1,458 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2018 Wandboard, Org.
> + * Copyright 2017 NXP
> + *
> + * Author: Richard Hu <hakahu@xxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mq.dtsi"
> +
> +/ {
> + model = "PICO-PI-8M";
> + compatible = "wand,imx8mq-pico-pi", "fsl,imx8mq";
The board compatible needs to be documented.
> +
> + chosen {
> + bootargs = "console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200";
The earlycon is only needed for debugging early hang issue. Do you
really want it by default? If no, we can save the 'bootargs' here,
since 'stdout-path' below will get you correct console setup.
> + stdout-path = &uart1;
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
Drop this container node and put fixed regulator directly under root
node.
> +
> + reg_usb_otg_vbus: usb_otg_vbus {
Please use node name like 'regulator-xxx'.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_otg_vbus>;
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 14 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
The 'pinctrl-names' is pointless if there is no 'pinctrl' property.
> +
> + wand-pi-8m {
Drop this container node.
> + pinctrl_otg_vbus: otgvbusgrp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x19 /* USB OTG VBUS Enable */
> + >;
> + };
> +
> + pinctrl_enet_3v3: enet3v3grp {
Sort these pinctrl nodes alphabetically.
> + fsl,pins = <
> + MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x19
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
> + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
> + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
> + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
> + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
> + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
> + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
> + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
> + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
> + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
> + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
> + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
> + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
> + MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B 0x49
> + MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B 0x49
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
> + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
> + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
> + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
> + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
> + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
> + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
> + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
> + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
> + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
> + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
> + >;
> + };
> +
> + pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> + fsl,pins = <
> + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x85
> + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc5
> + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc5
> + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc5
> + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc5
> + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc5
> + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc5
> + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc5
> + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc5
> + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc5
> + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x85
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> + fsl,pins = <
> + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x87
> + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc7
> + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc7
> + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc7
> + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc7
> + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc7
> + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc7
> + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc7
> + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc7
> + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc7
> + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x87
> + >;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2grpgpio {
> + fsl,pins = <
> + MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
> + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
> + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
> + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
> + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
> + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
> + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> + fsl,pins = <
> + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x85
> + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc5
> + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc5
> + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc5
> + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc5
> + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc5
> + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> + fsl,pins = <
> + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x87
> + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc7
> + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc7
> + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc7
> + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc7
> + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc7
> + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
> + >;
> + };
> +
> + pinctrl_pmic: pmicirq {
> + fsl,pins = <
> + MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
> + >;
> + };
> +
> + pinctrl_tusb320_irq: tusb320_irqgrp {
Please name the pinctrl node in a more consistent way, i.e. no
underscore.
> + fsl,pins = <
> + MX8MQ_IOMUXC_NAND_DATA00_GPIO3_IO6 0x41
> + >;
> + };
> +
> + pinctrl_typec_ss_sel: typec_ss_selgrp {
> + fsl,pins = <
> + MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19
> + >;
> + };
> + };
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1 &pinctrl_enet_3v3>;
> + phy-mode = "rgmii-id";
> + pinctrl-assert-gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
> + phy-handle = <ðphy0>;
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + at803x,led-act-blind-workaround;
> + at803x,eee-disabled;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + typec_tusb320:tusb320@47 {
> + compatible = "ti,tusb320";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tusb320_irq &pinctrl_typec_ss_sel>;
> + reg = <0x47>;
> + vbus-supply = <®_usb_otg_vbus>;
> + ss-sel-gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
> + tusb320,int-gpio = <&gpio3 6 GPIO_ACTIVE_LOW>;
> + tusb320,select-mode = <0>;
> + tusb320,dfp-power = <0>;
> + };
Where is the bindings doc for this device?
> +
> + pmic: pmic@4b {
> + reg = <0x4b>;
> + compatible = "rohm,bd71837";
> + /* PMIC BD71837 PMIC_nINT GPIO1_IO12 */
> + pinctrl-0 = <&pinctrl_pmic>;
> + gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>;
Where is the bindings for this property?
> +
> + regulators {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + buck1: BUCK1 {
> + regulator-name = "buck1";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + regulator-ramp-delay = <1250>;
> + rohm,dvs-run-voltage = <900000>;
> + rohm,dvs-idle-voltage = <850000>;
> + rohm,dvs-suspend-voltage = <800000>;
> + };
> +
> + buck2: BUCK2 {
> + regulator-name = "buck2";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + regulator-ramp-delay = <1250>;
> + rohm,dvs-run-voltage = <1000000>;
> + rohm,dvs-idle-voltage = <900000>;
> + };
> +
> + buck3: BUCK3 {
> + regulator-name = "buck3";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + rohm,dvs-run-voltage = <1000000>;
> + };
> +
> + buck4: BUCK4 {
> + regulator-name = "buck4";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + rohm,dvs-run-voltage = <1000000>;
> + };
> +
> + buck5: BUCK5 {
> + regulator-name = "buck5";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-boot-on;
> + };
> +
> + buck6: BUCK6 {
> + regulator-name = "buck6";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> +
> + buck7: BUCK7 {
> + regulator-name = "buck7";
> + regulator-min-microvolt = <1605000>;
> + regulator-max-microvolt = <1995000>;
> + regulator-boot-on;
> + };
> +
> + buck8: BUCK8 {
> + regulator-name = "buck8";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-boot-on;
> + };
> +
> + ldo1: LDO1 {
> + regulator-name = "ldo1";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2: LDO2 {
> + regulator-name = "ldo2";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3: LDO3 {
> + regulator-name = "ldo3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> +
> + ldo4: LDO4 {
> + regulator-name = "ldo4";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + };
> +
> + ldo5: LDO5 {
> + regulator-name = "ldo5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> +
> + ldo6: LDO6 {
> + regulator-name = "ldo6";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + };
> +
> + ldo7: LDO7 {
> + regulator-name = "ldo7";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> + };
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +};
> +
> +&uart1 { /* console */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> + bus-width = <4>;
> + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&usb3_phy0 {
> + status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> + extcon = <&typec_tusb320>;
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usb3_phy1 {
> + status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> + status = "okay";
> + dr_mode = "host";
We prefer to end the property list with 'status', so please flip the
order here.
Shawn
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&A53_0 {
> + operating-points = <
> + /* kHz uV */
> + 1500000 1000000
> + 1300000 1000000
> + 1000000 900000
> + 800000 900000
> + >;
> +};
> --
> 2.11.0
>
