Re: [PATCH v2 1/2] media: dt-bindings: add bindings for Toshiba TC358746

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Marco,

On Wed, Jun 19, 2019 at 05:28:37PM +0200, Marco Felsch wrote:
> Add corresponding dt-bindings for the Toshiba tc358746 device and update
> the MAINTAINERS file too.
>
> Signed-off-by: Marco Felsch <m.felsch@xxxxxxxxxxxxxx>

With Rob's blessing, I'm glad I didn't take you off-road with my
comments on v1 :)

Reviewed-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>

Thanks
   j

> ---
> Hi Rob,
>
> I droped your reviewed-by tag since there where several changes.
>
> Changes
> v2:
>  - use the Documentation/devicetree/bindings/media/ti,omap3isp.txt
>    formatting scheme
>  - Adapt introducing paragraph according Jacopo's comments
>  - drop the clock-names property
>  - drop the clock-lanes (csi-2) property
>  - adapt the property descriptions accroding Jacopo's comments
>  - use port@0 as input and port@1 as output port instead of mapping
>    port@0 to parallel and port@1 to csi-2 interface
>  - Adapt port/endpoint description according Jacopo's and Sakari's
>    comments
>  - Adapt the example
>  - squash v1 patch-3 and patch-1
>  - set status to Maintained
>
>  .../bindings/media/i2c/toshiba,tc358746.txt   | 95 +++++++++++++++++++
>  MAINTAINERS                                   |  7 ++
>  2 files changed, 102 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt
> new file mode 100644
> index 000000000000..e79b45ee050e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt
> @@ -0,0 +1,95 @@
> +Toshiba TC358746 Parallel to MIPI CSI2-TX or MIPI CSI2-RX to Parallel Bridge
> +============================================================================
> +
> +The Toshiba TC358746 converts a parallel into a MIPI CSI-2 stream. The direction
> +can be either parallel-in -> csi-out e.g. to connect a parallel camera to a
> +MIPI CSI-2 host or csi-in -> parallel-out e.g. to connect a parallel display to
> +a MIPI CSI-2 host. It's programmable trough I2C and SPI. The SPI interface is
> +only supported in parallel-in -> csi-out mode.
> +
> +Required properties
> +-------------------
> +
> +- compatible		: Shall be "toshiba,tc358746"
> +- reg			: Shall be <0x0e>
> +- clocks		: Phandle to the reference clock source
> +
> +Optional properties
> +-------------------
> +
> +- reset-gpios		: Phandle to the GPIO connected to the reset input pin
> +
> +Port nodes (required)
> +=====================
> +
> +The device node must contain two ports children nodes which should be grouped
> +within a 'ports' node. The first port describes the input connection, the second
> +one describes the output one. Each port shall contain one endpoint subnode that
> +connects to a remote device and specifies the bus type of the input and output
> +ports. Only one endpoint per port shall be present.
> +
> +More documentation on these bindings is available in [1].
> +
> +reg			: The interface:
> +			  0 - Input, either parallel or MIPI CSI-2
> +			  1 - Output, either parallel or MIPI CSI-2
> +
> +Endpoint nodes (required)
> +=========================
> +
> +Required properties
> +-------------------
> +
> +- bus-width		: Look at [1] for more information (Parallel endpoint)
> +- data-lanes		: Look at [1] for more information (CSI-2 endpoint)
> +- link-frequencies	: Array of frequencies the driver can choose to
> +			  full-fill the parallel timings calculation. Look at
> +			  [1] for more information (CSI-2 endpoint)
> +
> +Optional properties
> +-------------------
> +
> +- bus-type		: Look at [1] for more information
> +- clock-noncontinuous	: Look at [1] for more information (CSI-2 endpoint)
> +
> +[1] Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +Example
> +=======
> +
> +&i2c {
> +	csi-bridge@0e {
> +		reg = <0x0e>;
> +		compatible = "toshiba,tc358746";
> +		pinctrl-names = "default";
> +		clocks = <&clk_cam_ref>;
> +		reset-gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			/* Input */
> +			port@0 {
> +				reg = <0>;
> +
> +				tc358746_parallel_in: endpoint {
> +					bus-width = <8>;
> +					remote-endpoint = <&micron_parallel_out>;
> +				};
> +			};
> +
> +			/* Output */
> +			port@1 {
> +				reg = <1>;
> +
> +				tc358746_mipi2_out: endpoint {
> +					remote-endpoint = <&mipi_csi2_in>;
> +					data-lanes = <1 2>;
> +					clock-noncontinuous;
> +					link-frequencies = /bits/ 64 <216000000>;
> +				};
> +			};
> +		};
> +	};
> +};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 57f496cff999..833b3c8fb301 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -15955,6 +15955,13 @@ S:	Maintained
>  F:	drivers/media/i2c/tc358743*
>  F:	include/media/i2c/tc358743.h
>
> +TOSHIBA TC358746 DRIVER
> +M:	Marco Felsch <kernel@xxxxxxxxxxxxxx>
> +L:	linux-media@xxxxxxxxxxxxxxx
> +S:	Maintained
> +F:	drivers/media/i2c/tc358746*
> +F:	Documentation/devicetree/bindings/media/i2c/toshiba,tc358746.txt
> +
>  TOSHIBA WMI HOTKEYS DRIVER
>  M:	Azael Avalos <coproscefalo@xxxxxxxxx>
>  L:	platform-driver-x86@xxxxxxxxxxxxxxx
> --
> 2.20.1
>

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux