On Tue, May 28, 2019 at 05:57:44AM -0700, Angus Ainslie (Purism) wrote: > The Librem5 devkit is based on the imx8mq from NXP. This is a default > devicetree to boot the board to a command prompt. > > Changes since v14: > > Add regulator-always-on for the SNVS regulators. > Added pgc nodes. > Fixed charger pre-current. Since Pavel was reviewing your patches, you should copy him on the new version. Has this version addressed all his review comments? Shawn > > Changes since v13: > > Moved haptic motor from pwm-led to gpio-vibrator. > Cleaned up regulator node naming. > Whitescpace cleanup. > Re-indent pinmux stanzas. > Drop pwm2 node. > Drop MAINTAINERS patch. > > Changes since v12: > > Updated patch to vendor-prefixes.yaml. > Dropped always on from regulators. > > Changes since v11: > > Added reviewed-by tags. > Fixed subject typo. > > Changes since v10: > > Moved MAINTAINERS entry to "ARM/FREESCALE IMX" section > > Changes since v9: > > Added a MAINTAINERS entry for arm64 imx devicetree files. > > Changes since v8: > > Fixed license comment. > Changed regulators to all lower case. > Changed clock frequency for NXP errata e7805. > Dropped blank line. > > Changes since v7: > > More regulators always on for USB. > Add vbus regulator. > Drop vbat regulator. > Replace legacy "gpio-key,wakeup" with "wakeup-source". > Add vbus-supply to get rid of warning > imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply vbus not found, > using dummy regulator > > Changes since v6: > > Dropped unused regulators. > Fix regulator phandles case. > Dropped extra whitespace. > > Changes since v5: > > Added reviewed-by tags. > Moved USB port links to USB controller node. > > Changes since v4: > > Compiled against linux-next next-20190415. > Added imx8mq to the arm yaml file. > Re-arrange regulator nodes to drop undefined supplies. > Additional ordering for aesthetics. > Split some long lines. > Added lots of blank lines. > Moved pinctl muxes to where they are used. > Cleaned out reg defintions from regulator nodes. > > Changes since v3: > > Freshly sorted and pressed nodes. > Change the backlight to an interpolated scale. > Dropped i2c2. > Dropped devkit version number to match debian MR. > > Changes since v2: > > Fixed incorrect phy-supply for the fsl-fec. > Dropped unused regulator property. > Fixup Makefile for linux-next. > > Changes since v1: > > Dropped config file. > Updated the board compatible label. > Changed node names to follow naming conventions. > Added a more complete regulator hierachy. > Removed unused nodes. > Removed unknown devices. > Fixed comment style. > Dropped undocumented properties. > > Angus Ainslie (Purism) (3): > arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit > dt-bindings: Add an entry for Purism SPC > dt-bindings: arm: fsl: Add the imx8mq boards > > .../devicetree/bindings/arm/fsl.yaml | 7 + > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../dts/freescale/imx8mq-librem5-devkit.dts | 806 ++++++++++++++++++ > 4 files changed, 816 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts > > -- > 2.17.1 >
