> -----Original Message-----
> From: Andy Tang
> Sent: Monday, May 27, 2019 3:27 AM
> To: Leo Li <leoyang.li@xxxxxxx>
> Cc: Shawn Guo <shawnguo@xxxxxxxxxx>; Rob Herring
> <robh+dt@xxxxxxxxxx>; Mark Rutland <mark.rutland@xxxxxxx>;
> moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE <linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx>; open list:OPEN FIRMWARE AND FLATTENED
> DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>; lkml <linux-
> kernel@xxxxxxxxxxxxxxx>
> Subject: RE: [EXT] Re: [PATCH] arm64: dts: ls1028a: Add temperature sensor
> node
>
> Hi Leo,
>
> > -----Original Message-----
> > From: Li Yang <leoyang.li@xxxxxxx>
> > Sent: 2019年5月25日 6:32
> > To: Andy Tang <andy.tang@xxxxxxx>
> > Cc: Shawn Guo <shawnguo@xxxxxxxxxx>; Rob Herring
> <robh+dt@xxxxxxxxxx>;
> > Mark Rutland <mark.rutland@xxxxxxx>; moderated list:ARM/FREESCALE
> IMX
> > / MXC ARM ARCHITECTURE <linux-arm-kernel@xxxxxxxxxxxxxxxxxxx>;
> > open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> > <devicetree@xxxxxxxxxxxxxxx>; lkml <linux-kernel@xxxxxxxxxxxxxxx>
> > Subject: [EXT] Re: [PATCH] arm64: dts: ls1028a: Add temperature sensor
> > node
> >
> > Caution: EXT Email
> >
> > On Thu, May 23, 2019 at 8:30 PM Yuantian Tang <andy.tang@xxxxxxx>
> > wrote:
> > >
> > > Add nxp sa56004 chip node for temperature monitor.
> > >
> > > Signed-off-by: Yuantian Tang <andy.tang@xxxxxxx>
> > > ---
> > > arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 5 +++++
> > > arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 5 +++++
> > > 2 files changed, 10 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> > > b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> > > index b359068d9605..31fd626dd344 100644
> > > --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> > > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> > > @@ -131,6 +131,11 @@
> > > compatible = "atmel,24c512";
> > > reg = <0x57>;
> > > };
> > > +
> > > + temp@4c {
> >
> > The recommended name for temperature senor in dts spec is
> > temperature-sensor.
> I didn't find the spec for this recommendation. Could you please provide the
> link?
You can find the spec on https://www.devicetree.org/
> I like to update it to temp-sensor though.
>
> >
> > > + compatible = "nxp,sa56004";
> >
> > The binding says the following property is required. If it is not the
> > case, probably we should update the binding.
> > - vcc-supply: vcc regulator for the supply voltage.
> I will add the vcc-supply to comply this requirement.
>
> Thanks,
> Andy
> >
> > > + reg = <0x4c>;
> > > + };
> > > };
> > >
> > > i2c@5 {
> > > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> > > b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> > > index f9c272fb0738..012b3f8696b7 100644
> > > --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> > > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> > > @@ -119,6 +119,11 @@
> > > compatible = "nxp,pcf2129";
> > > reg = <0x51>;
> > > };
> > > +
> > > + temp@4c {
> > > + compatible = "nxp,sa56004";
> > > + reg = <0x4c>;
> > > + };
> > > };
> > > };
> > > };
> > > --
> > > 2.17.1
> > >
